Abstract:Generally, the function of thermal interface material (TIM) is filling rough surfaces, eradicating air pockets, decreasing thermal resistance, and improving heat dissipating effects. On this basis, we provide the TIM with another identity, "adhesion", rendering it not only play a role of heat dissipation, but also serve as an adhesive to bond contacting surfaces. In this work, nano- to microscopic liquid metal (LM) droplets are embedded into the epoxy matrix to fabricate a LM-epoxy in-situ cured composite. By adding the curing agent, the LM-epoxy composite is cured into an entity structure, transforming from an amorphous grease state to a self-adaptive pad state. When the average droplet size is in a reasonable range of approximately 5–25 μm, the composite's thermal resistance ( R total ) decreases to 2.19 mm 2 K/W at 70% volume fraction with its adhesive strength of 0.497 MPa, and the thermal conductivity ( k TIM ) could increase to 10.05 W/(m·K) at 85%. Both R total and k TIM change rapidly for droplet size approximately ranging from 10 2 nm to 10 1 μm and then tend to level off when it further increases to 10 2 μm. A conception of equivalent contact thickness, δ, is presented to elucidate the contacting thermal resistance R c , and set up predictive models of R total for different volume fractions by considering the microscopic interfacial thermal resistance R b between filler and matrix or not. This composite simultaneously possesses characteristics of the low thermal resistance like thermal grease, the whole entity like thermal pad, and the anti-leak characteristics by in-situ cured process. Actual cooling tests show it has a considerable temperature difference of 4.75 °C lower than the commercial thermal grease at 650 W heating power. This in-situ cured strategy, via decreasing the thermal resistance and solving the problem of LM leakage, remarkably promotes the LM-TIMs achieving a broader application prospect in the future.

Fabrication of silicone-based gap filler for electric vehicles using magnesium oxide thermally conductive fillers

Thermal Interface Materials with Sufficiently Vertically Aligned and Interconnected Nickel-Coated Carbon Fibers under High Filling Loads Made Via Preset-Magnetic-field Method

Enhancement of thermal conductivity and insulation of silicone thermal interface material through surface modification and synergistic effects of nanofillers for thermal management of electronic devices

High-performance non-silicone thermal interface materials based on tunable size and polymorphic liquid metal inclusions

Synergistic Enhanced Thermal Conductivity of Polydimethylsiloxane Composites Via Introducing SCF and Hetero-Structured GB@rGO Hybrid Fillers

Multi‐contact Hybrid Thermal Conductive Filler Al2O3@AgNPs Optimized Three‐dimensional Thermal Network for Flexible Thermal Interface Materials

Dual-direction Thermal Conductive FG-based Composite Manufactured by Rotating Magnetic-Field Assisted Casting

Effect of Surface Functionalization of Si3N4 Fillers on Thermal and Mechanical Properties of TIMs

Thermally conductive silicone rubber composites with vertically oriented carbon fibers: A new perspective on the heat conduction mechanism

Soft and Damping Thermal Interface Materials with Honeycomb-Board-Mimetic Filler Network for Electronic Heat Dissipation

Multi‐contact hybrid thermal conductive filler Al 2 O 3 @ AgNPs optimized three‐dimensional thermal network for flexible thermal interface materials

Controlled High Filler Loading of Functionalized Al2O3-Filled Epoxy Composites for LED Thermal Management

Anti-leak, self-adaptive liquid metal-epoxy in-situ cured composites with ultra-low thermal resistance via flexible droplet inclusions

Phase Change Materials Coated with Modified Graphene-Oxide As Fillers for Silicone Rubber Used in Thermal Interface Applications

Nano-capsuled thermal interface materials filler using defective multilayered graphene-coated silver nanoparticles

Alveoli‐Mimetic Synergistic Liquid and Solid Thermal Conductive Interface as a Novel Strategy for Designing High‐Performance Thermal Interface Materials

Thermally conductive and highly electrically resistive grease through homogeneously dispersing liquid metal droplets inside methyl silicone oil

Improving through-plane thermal conductivity of PDMS-based composites using highly oriented carbon fibers bridged by Al2O3 particles

High Voltage Special Issue: Thermally Conductive but Electrically Insulating Materials For High Voltage Applications

Fabrication of high-performance thermally conductive and electrically insulating polymer composites with siloxane/multi-walled carbon nanotube core-shell hybrids at low filler content

The polymer-based thermal interface materials with improved thermal conductivity, compression resilience, and electromagnetic interference shielding performance by introducing uniformly melamine foam