Abstract:Resource characterization and modelling are important in exploration wherein cores of rock are extracted from the surface. Such cores not only help to assess the quantity and quality of the mineral or ore but also provide means to establish an excavation and ground control regime for different types of mining. Prediction of coring rate assumes critical importance for planning the coal mines which have fragile nature of ground posing challenges in strata control and excavation performance. Coring rate or associated rock factors characterize the rockmass to help in this regard. In line with the above need, the geological and machine performance data of two representative boreholes drilled at 90° and 80° in a complex coal bearing strata were collected covering drill machine variables, penetration rates and physico-mechanical properties of the rock cores in laboratory. The penetration rate showed significant deviation up to a depth of 250 m from the surface in both the holes. The variation in penetration rate was 28% in basalt and 38% in mudstone, 16% in sandy shale with coal, 10% in sandy shale and − 2% in medium to coarse grained sandstone. In order to model the penetration rate, a rock designation factor was devised in terms of the depth, tensile strength and density of the rockmass. The rock designation factor along with other machine variables were analyzed initially using PCA enabled Gaussian progression method which helped in model refinement and selection of best variables. Subsequently, response surface analysis of selected variables viz., rock designation factor, torque, drill fluid pressure and RPM, using multivariate non-linear ANOVA with backpropagation method to develop a penetration rate model. Drill angle and rock type were retained as categorial factors. The model thus devised was evaluated using various techniques and resulted in RMSE of 8.1, MAE of 5.59, MSE of 65.61 with predicted R2 of 0.927. The intercepts for different rocks analyzed were thus enumerated. The model developed can be used for defining penetration rates for the type of drill investigated. Explicit surface response with variations in different variables could thus be defined along with the relative sensitivity of the variables entering into the interaction with perturbation method. Also, a variation of 50 mm/min in penetration rates in 90° and 80°drilling is accounted by the model. The penetration rate prediction model is sensitive to the rock designation factor, RPM, drill fluid pressure, angle of drilling and torque in decreasing order. It is observed that the best penetration rate can be achieved at an average RPM of 436 and minimum drill fluid pressure of 6 kg/cm2, indicating that higher drill fluid pressures may not favor higher penetration rates.Article highlightsData of two holes drilled at 90° and 80° upto a depth of 326 m in complex Gondwana Region were investigated for effect of machine and rock properties on penetration rate.Exploratory data analysis revealed significant effect of depth on penetration rate upto 250 m. A Rock Designation Factor comprising of depth of rock, density and tensile strength was developed to address different modelling issues.Multivariate analysis of the data along with principal component analysis was used to select the variables for modelling. Response surface analysis, was used to develop a multivariate model for prediction of penetration rate that helped to identify the sensitivity of the variables.

Application of DFN approach for the selection of maximized penetration rate model of TBM in hard rock

Introduction of a modified QTBM model for predicting TBM penetration rate in rock, based on data from mechanized tunneling projects in Iran

Performance Evaluation of TBM Using an Improved Load Prediction Model

Prediction of TBM performance in fresh through weathered granite using empirical and statistical approaches

An empirical method for estimating TBM penetration rate using tunnelling specific energy

A mechanical method for predicting TBM penetration rates

Evaluation of Hard Rock Tunnel Boring Machine (TBM) Performance Using Stochastic Modeling

Predicting tunnel boring machine penetration rate utilizing geomechanical properties

Decoding rate of penetration of tunnel boring machine in Deccan Traps under varied geological and machine variables using response surface analysis

TBM performance analysis in very strong and massive rocks; case study: Kerman water conveyance tunnel project, Iran

Rock mass characteristics model for TBM penetration rate prediction– an updated version

Does the Selection of the Fracture Model Affect the Calculation of the Permeability of a Rock Mass?

A hybrid GEP and WOA approach to estimate the optimal penetration rate of TBM in granitic rock mass

A case study of TBM performance prediction using field tunnelling tests in limestone strata

Prediction of optimum TBM penetration strategy with minimum energy consumption in hard rocks

Supervised Machine Learning Techniques to the Prediction of Tunnel Boring Machine Penetration Rate

Estimation of the performance of the tunnel boring machine (TBM) using uniaxial compressive strength and rock mass rating classification (RMR)–A case study from the Deccan traps, India

Analysis of rock cuttability based on excavation parameters of TBM

Prediction of TBM Disc Cutter Wear and Penetration Rate in Tunneling Through Hard and Abrasive Rock Using Multi-layer Shallow Neural Network and Response Surface Methods

Investigations on the influence of rock and machine characteristics on coring rates in vertical and mildly inclined exploration drilling in complex coal bearing rock formation

Rock Chip Properties of TBM Penetration in Jointed Rock Masses Based on an Improved DICE2D Simulation