Abstract:Effective thermal conduction between solid interfaces has emerged as a major bottleneck in heat dissipating heat from new-generation high-performance electronics. Gallium-based liquid metals (LMs), known for their high thermal conductivity, are gaining significant traction as thermal interface materials (TIMs) for enhanced thermal management. In this work, to address the key issues facing the application of gallium-based LMs as TIMs, including the lack of composition ratio data, poor coating performance and the need for improved thermal conductivity, two types of gallium-based LM-TIMs (Ga-In binary LM-TIMs and Ga-In-Sn ternary LM-TIMs) with different composition ratios were experimentally prepared, investigated and optimized. The thermal conductivities of the LM-TIMs at different temperatures (80 - 120 ℃) were tested, and the application reliability of the LM-TIMs was optimized by continuously destructing the oxide layer and filling micro copper particles. The influence of optimization parameters such as the duration of the destruction of oxide layer, the filling ratios of the particles and the particle size on the operation performance of the LM-TIMs was studied and analyzed. The results showed that the LM-TIMs exhibited excellent thermal conductivities of 29.6 - 38.5 W/(m·K), and the thermal conductivity increased with indium mass fraction and decreased with tin mass fraction. Significant improvements in coating performance were observed with the increase of the duration of destructing oxide layer, but it led to a reduction in thermal conductivity. Balancing coating performance and thermal conductivity, it was found that 30 min was the ideal duration. The filling of micro particles made up for the reduced thermal conductivity, and higher filling ratios and smaller particle sizes achieved better enhancement. In the experiment, a filling ratio of 5 % was appropriate because solidification occurred in LM-TIMs at higher filling ratios which weakened the thermal conductivity. This work provided valuable reference for the application and optimization of high thermal conductive gallium-based LM-TIMs.

Thermal Interface Materials with High Thermal Conductivity and Low Young's Modulus Using a Solid-Liquid Metal Codoping Strategy

Low Interfacial Thermal Resistance Between Crossed Ultra-Thin Carbon Nanothreads

Experimental Investigation on Optimization of the Performance of Gallium-Based Liquid Metal with High Thermal Conductivity As Thermal Interface Material for Efficient Electronic Cooling

Joint‐Inspired Liquid and Thermal Conductive Interface for Designing Thermal Interface Materials with High Solid Filling yet Excellent Thixotropy

Strategies for enhancing thermal conductivity of polymer-based thermal interface materials: a review

High-performance non-silicone thermal interface materials based on tunable size and polymorphic liquid metal inclusions

Alveoli‐Mimetic Synergistic Liquid and Solid Thermal Conductive Interface as a Novel Strategy for Designing High‐Performance Thermal Interface Materials

High performance liquid metal thermal interface materials

Pressure induced thermal conduction paths in liquid metal-boron nitride fillered thermal interface materials with high thermal conductivity

Thermally Conductive Yield‐Stress Fluids with Reversible Solid–Liquid Transition Used as Thermal Interface Materials for Heat Dissipation of Chips

Compliance-tunable thermal interface materials based on vertically oriented carbon fiber arrays for high-performance thermal management

Anti-leak, self-adaptive liquid metal-epoxy in-situ cured composites with ultra-low thermal resistance via flexible droplet inclusions

An efficient thermal interface material with anisotropy orientation and high through-plane thermal conductivity

Joint‐Inspired Liquid and Thermal Conductive Interface for Designing Thermal Interface Materials with High Solid Filling yet Excellent Thixotropy (Adv. Funct. Mater. 14/2023)

Fabrication of liquid metal/diamond hybrid thermal interface materials with high thermal conductivity and low flowability

A Review of Advanced Thermal Interface Materials with Oriented Structures for Electronic Devices

A Novel Phase Change Composite with Ultrahigh Through-Plane Thermal Conductivity and Adjustable Flexibility

Poly(ionic liquid)s: A Promising Matrix for Thermal Interface Materials

PDMS/functionalized h-BN/liquid metal flexible composite with dual-network structure for achieving superior thermal conductivity and low thermal resistance via interfacial grafting

Innocuous, Highly Conductive, and Affordable Thermal Interface Material with Copper-Based Multi-Dimensional Filler Design

Laminar Metal Foam: A Soft and Highly Thermally Conductive Thermal Interface Material with a Reliable Joint for Semiconductor Packaging.