Abstract:A two-step time-to-digital converter (TDC) is designed for the high-precision time measurement of the DIRC-like TOF (DTOF) detector at the Super Tau-Charm Facility (STCF). Extending the measurement range by Nutt's method, the TDC clock cycle is interpolated with two voltage-controlled tapped delay lines (TDL) connected by a dual-slope time amplifier (TA). By amplifying the residue from the first-step TDL-based interpolation with the TA and measuring it with the second TDL, the TDC resolution is significantly improved to sub-gate delay. Since the residue is extracted by a new method without the need of TA duplication or delay insertion, the TDC power consumption and conversion time are effectively reduced. By adopting the improved TA circuit into the TDC with a high gain, adjustable output offsets, and good linearity, the TDC measurement precision is guaranteed. In addition, a new DLL structure is proposed to stabilize the TDL against process, voltage, and temperature (PVT) variations with less power consumption. Benefiting from the proposed residue extraction method and DLL structure, the TDC exhibits low power consumption. To verify the TDC design, a prototype chip with two TDC channels is fabricated in GlobalFoundries (GF) 180 nm CMOS technology for performance evaluation. With a system clock of 150 MHz, it has a resolution (LSB) of 16.5 ps and a maximum sample rate of 6 MS/s. The differential nonlinearity (DNL) error ranges from - 0.98 LSB to 0.87 LSB and the integral nonlinearity error (INL) ranges from- 4.21 LSB to 2.83 LSB. With a bin-by-bin calibration method, the measured TDC precision is 12.1 ps on average within the 0-20 ns time interval measurement range. In addition, the TDC has low temperature sensitivity and does not require recalibration within a 20 C-degrees temperature range. Each TDC channel consumes 434 mu W power at 1 MS/s sample rate. The test results confirm that the proposed TDC can achieve high precision with a moderate sample rate and low power consumption without highly scaled technologies, which can meet the requirements of the DTOF detector at STCF.

Digital duty-cycle correction circuit for clock paths in radiation-tolerant high-speed wireline transmitters

A novel high-accuracy clock stabilizer with 50% duty cycle

A Radiation-Tolerant 25.6-Gb/s High-Speed Transmitter in 28-nm CMOS With a Tolerance of 1 Grad

2.5 Mw 2.73 GHz Non-Overlapping Multi-Phase Clock Generator with Duty-Cycle Correction in 0.13 Μm CMOS

A Low Noise Fault Tolerant Radiation Hardened 2.56 Gbps Clock-Data Recovery Circuit With High Speed Feed Forward Correction in 65 nm CMOS

Development of radiation tolerance evaluation and measurement system for spaceborne D/A converter

A 20 GHz High Speed, Low Jitter, High Accuracy and Wide Correction Range Duty Cycle Corrector.

An Improved Clock Cycle Measurement Method for High-Speed Serial Signal with Duty-Cycle-Distortion Jitter

A Clock Delivery Path with Peaking Buffers for 112Gb/s Wireline Transceiver

A Reference-Less All-Digital Burst-Mode CDR with Embedded TDC.

A Half Rate CDR with DCD Cleaning Up and Quadrature Clock Calibration for 20gbps 60ghz Communication in 65nm CMOS.

Simulation Studies on the Transient Dose Rate Effect of Analog Delay Locked Loops

A 12 Ps Precision Two-Step Time-to-Digital Converter Consuming 434 $\mu$ W at 1 MS/s in 180 Nm CMOS with a Dual-Slope Time Amplifier

A 20-Ps Time-to-Digital Converter (TDC) Implemented in Field-Programmable Gate Array (FPGA) with Automatic Temperature Correction

A 10gbps Half-Rate Digital Clock and Data Recovery Circuit for 60ghz Receiver in 65nm CMOS

Design of a high-precision time-to-digital converter in an Elitestek Ti60 field-programmable-gate-array

A High-Resolution Pipeline Time-to-digital Converter in 0.18μm CMOS Technology

A Full Digitizing Design of Measuring Systems in Diagnosing of High-Intensity Pulsed Radiation Field

Low Power 16-channel Wave Union TDC in a Radiation Tolerant FPGA

A 0.18 μm CMOS 10-Gb/S multichannel transmitter with duty-cycle correction