Abstract:Copper (Cu)-stainless steel (SS 304L) multi-material is enduring research topic for various engineering applications such as tooling industry, aerospace, power-generation and cryogenic applications. Laser directed energy deposition (LDED) based additive manufacturing is a one of the promising technologies for fabricating Cu-SS multi-material component. However, LDED of Cu-SS is difficult due to the significant difference in thermo-physical properties and poor solubility of Cu and Fe. One of the methods to overcome this issue is adopting a functionally graded material (FGM) approach. In this pretext, the fabrication of Cu-SS FGM using the LDED process is taken up in the present study with three different Cu compositional grading approaches, such as direct (GD100Cu), 50 % (GD50Cu) and 20 % (GD20Cu). The LDED process windows for single tracks and bulk deposition of Cu-SS FGM are identified by varying the laser power, scan speed and composition of Cu and SS304L. Subsequently, the identified process window is used to deposit bulk structures of Cu-SS FGM. The LDED-built Cu-SS FGMs are characterized in terms of build quality, chemical composition, microstructural evolution and mechanical behavior. Microscopic analysis reveals, the defect-free deposition of GD100Cu and GD50Cu, at identified process parameters. For GD20Cu, the micro-crack formation in the graded region and inter-layer porosity in the Cu-rich region are two competing phenomenon, and it is observed that layer-wise increase in laser power and interlayer delay leads to minimum crack density and lower porosity. Further, increase in Cu content leads to significant change in microstructural morphology from columnar dendrites to fine cellular morphology. In Cu-SS FG structures, the chemical composition and mechanical properties are found to be changing gradually. Further, obtained ultimate tensile strength (UTS) of GD100Cu and GD50Cu is found higher than GD20Cu and the mode of failure is found to be ductile. The improved UTS in GD100Cu and GD50Cu in comparison with pure Cu arises due to formation of nano precipitate of Cu in the inter-dendritic zone of Fe rich phase. This establishes the suitability of LDED for building FG Cu-SS components at GD50Cu over GD20Cu.

Functionally Gradient H13 Tool Steel/Oxygen‐Free High Thermal Conductivity Cu Composites Manufactured by Laser‐Directed Energy Deposition

Elucidating laser directed energy deposition based additive manufacturing of copper-stainless steel functionally graded material: Processing and material behavior

The Effect of Thermal Cycling on Direct Laser-Deposited Gradient H13 Tool Steel: Microstructure Evolution, Nanoprecipitation Behaviour, and Mechanical Properties

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

Rapid Fabrication of Functionally Gradient Material Parts by Laser Beam

Laser Deposition of Ti6Al4V-316L Composition Gradient Structure: Challenge on Intermetallics

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Microstructure and mechanical properties of H13 tool steel fabricated by high power laser powder bed fusion

Simulation and Study of Manufacturing of W–Cu Functionally Graded Materials by a Selective Laser Melting Process

Physical and Mechanical Properties of Cu-Fe System Functionally Graded and Multimaterial Structures after the DED

Copper-nickel functionally magnetic gradient material fabricated via directed energy deposition

Deposition of Functionally Graded Material Fabricated by Robot Plasma Arc Welding

On the composition gradient of steel/Invar functionally graded material manufactured by wire-based direct energy deposition

Microstructure and Mechanical Properties of H13 Steel/High-Speed Steel Composites Prepared by Laser Metal Deposition

Microstructural and Hardness Behavior of H13 Tool Steel Manufactured by Ultrasound-Assisted Laser-Directed Energy Deposition

Microstructure Evolution of Copper/steel Gradient Deposition Prepared Using Electron Beam Freeform Fabrication

Spatially heterogeneous microstructure in in-situ TiO-reinforced Ti6Al4V/316L functionally graded material fabricated via directed energy deposition

Preparation of WC Reinforced Co-Based Alloy Gradient Coatings on a H13 Mold Steel Substrate by Laser Cladding

Development and Characterization of 316l/inconel625 Functionally Graded Material Fabricated by Laser Direct Metal Deposition

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

Functionally Graded Additive Manufacturing of Thin-Walled 316L Stainless Steel-Inconel 625 by Direct Laser Metal Deposition Process: Characterization and Evaluation