Abstract:SUMMARY: Porous titanium alloy scaffold was widely used in treating bone defect caused by traumatic injury and osteomyelitis, which was incapable of self-healing. The implantation of scaffold produced stress shielding thereby forming osteolysis. The objective of this study was to analysis trabecular morphological features of osseointegrated bone. 14 New Zealand rabbits were divided into two groups, surgery group and healthy control group. 7 rabbits in surgery group were selected to perform 3D printed porous titanium alloy scaffold implantation surgery with preload at the defect of femoral condyle for osseointegration. The other 7 rabbits in control group were feed free. After 90 days healing, femoral condyles were extracted to perform micro-CT scanning with hydroxyapatite calibration phantom. Mean bone mineral density (BMD), bone volume fraction (BV/TV), BS/TV (bone surface area ratio), Tb.Th (thickness of trabeculae), Tb.N (number of trabeculae), Tb.Sp (trabecular separation) and DA (degree of anisotropy) were calculated from micro-CT images. The results revealed that osseointegration inside and at the surface of scaffolds worked well from grey values of micro-CT images. After 12 weeks healing, mean bone mineral densities (BMD) in surgery group and healthy control group were calculated as 80020mg/cm3 and 98090mg/cm3, respectively. This revealed that the strength of trabeculae in surgery group might lower than that in the healthy group. Trabecular morphological parameters test showed that trabecular morphological parameters at the surface of scaffolds in the surgery group deteriorated significantly. It was found from micro-CT images that ingrowth bone was filled with pores of scaffold. Overall, the effect of osseointegration was promoted through the change of mechanical micro-environment in the scaffold region. Overall, preload could improve osseointegration effect in the long-term after surgery. However, the trabecular morphology in the surgery group was deteriorated, which might bring secondary fracture risk again. RESUMEN: La malla de aleacin de titanio poroso se us ampliamente en el tratamiento de defectos seos causados por lesiones traumticas y osteomielitis. El implante de la malla gener una proteccin contra el estrs, formando as osteolisis. El objetivo de este estudio fue analizar las caractersticas morfolgicas trabeculares del hueso osteointegrado. Se dividieron 14 conejos (Neozelandeses) en dos grupos, grupo ciruga y grupo control saludable. Se seleccionaron 7 conejos en el grupo de ciruga para realizar una implantacin de mallas de aleacin de titanio poroso, impresas en 3D con precarga en el defecto del cndilo femoral para la osteointegracin. Los 7 conejos restantes del grupo control se mantuvieron sin alimentacin. Despus de 90 das de curacin, se extrajeron los cndilos femorales para realizar una exploracin por micro-CT con un espectro de calibracin de hidroxiapatita. Se calcularon a partir de imgenes de micro-CTDensidad mineral sea media (DMO), fraccin de volumen seo (BV / TV), BS / TV (relacin de rea de superficie sea), Tb.Th (espesor de trabculas), Tb.N (nmero de trabculas), Tb.Sp (trabecular separacin) y DA (grado de anisotropa). Los resultados revelaron que la osteointegracin dentro y en la superficie de los andamios funcion bien a partir de los valores grises de las imgenes de micro-CT. Despus de 12 semanas de curacin, las densidades medias de minerales seos (DMO) en el grupo ciruga y en el grupo control sano se calcularon como 800 20 mg/cm3 y 980 90 mg/cm3, respectivamente. Esto revel que la fuerza de las trabculas en el grupo de ciruga podra ser menor que la del grupo sano. La prueba de parmetros morfolgicos trabeculares mostr que en el grupo de ciruga, la superficie de las mallas, se deterioraron significativamente. Se descubri a partir de imgenes de microCT que el hueso en crecimiento estaba lleno de poros de andamio. En general, el efecto de la osteointegracin se promovi mediante el cambio del microambiente mecnico en la regin de la malla. En general, la precarga podra mejorar el efecto de osteointegracin a largo plazo despus de la ciruga. Sin embargo, la morfologa trabecular en el grupo de ciruga se deterior, lo que podra traer un nuevo riesgo de fractura secundaria.

Dura mater assists 3D printed porous titanium scaffolds in healing rabbit calvarial defects

[A Study on the Repair of Bone Defects with Deproteinized Bone Surrounded by Titanium Mesh and Osteoblasts].

Tuning Pore Features of Mineralized Collagen/pcl Scaffolds for Cranial Bone Regeneration in a Rat Model.

Enhanced Osseointegration of Porous Titanium Scaffold Implanted with Preload: An Experiment Study in Rabbits

3D Biomimetic Porous Titanium (Ti6Al4V ELI) Scaffolds for Large Bone Critical Defect Reconstruction: An Experimental Study in Sheep

Histological and biomechanical study of repairing rabbit radius segmental bone defect with porous titanium]

A fully ingrowing implant for cranial reconstruction: Results in critical size defects in sheep using 3D-printed titanium scaffold

3D Printed Triply Periodic Minimal Surface Ceramic Scaffold Loaded with Bone Morphogenetic Proteins-2 and Zoledronic for Cranium Defect repairment

Mussel inspired 3D elastomer enabled rapid calvarial bone regeneration through recruiting more osteoprogenitors from the dura mater

Examining trabecular morphology and chemical composition of peri-scaffold osseointegrated bone

The effect of pore size and porosity of Ti6Al4V scaffolds on MC3T3-E1 cells and tissue in rabbits

Three-Dimensional Printed Titanium Scaffolds Enhance Osteogenic Differentiation and New Bone Formation by Cultured Adipose Tissue-Derived Stem Cells Through the IGF-1R/AKT/Mammalian Target of Rapamycin Complex 1 (mTORC1) Pathway

Titanium alloy scaffold with controlled internal architecture as an osteoblast carrier to repair rabbit defects

3D Printed Bone Graft Material AP40mod Repair Calvarium Defect in Rabbit

In vivo study of dual functionalized mussel-derived bioactive peptides promoting 3D-printed porous Ti6Al4V scaffolds for repair of rabbit femoral defects

Treatment options for critical size defects - Comparison of different materials in a calvaria split model in sheep

The Mechanical Properties and Biometrical Effect of 3D Preformed Titanium Membrane for Guided Bone Regeneration on Alveolar Bone Defect

In Vitro and In Vivo Analysis of the Effects of 3D-Printed Porous Titanium Alloy Scaffold Structure on Osteogenic Activity

Bone regeneration in 3D printing bioactive ceramic scaffolds with improved tissue/material interface pore architecture in thin-wall bone defect

The Effects of Structural & Materials Design on the Mechanisms of Tissue Integration with the 3D Printed Polyether-Ether-Ketone Cranial Implants in Vivo

Reconstruction of Critical Sized Calvarial Defects by Porous Nano-Hydroxyapatite/polyamide 6 Composite with Bone Marrow Mesenchymal Stem Cells in Rat