Abstract:Two different sequences are considered: Method (I) cut‐then‐age: cut into 1‐cm wide strips and then expose to stress, and Method (II) age‐then‐cut: expose a larger sheet to stress and then cut into 1‐cm widths for mechanical property measurements. The data suggest that for UV exposures, the specimens should be cut after aging and the exposed side specimens discarded, and that for pressure cooker test exposures, the specimens should be cut before the exposureIn this study, we highlight some important factors in the specimen preparation methods for evaluating photovoltaic backsheet properties after accelerated aging. Two different sequences are considered: Method (I) cut‐then‐age: cut into 1‐cm wide strips and then expose to stress, and Method (II) age‐then‐cut: expose a larger sheet to stress and then cut into 1‐cm widths for mechanical property measurements. We also compare the effect of three cutting methods, (a) tensile specimen punch, (b) paper cutter, and (c) fresh razor blade. Several commercial backsheets were evaluated, with stress exposures including (a) pressure cooker test (PCT), (b) dry ultraviolet (UV) radiation exposure, and (c) UV combined damp heat tests. Fourier transform infrared spectrometer (FTIR) and intrinsic viscosity (IV) were used to analyze the materials on unstressed materials and samples exposed to PCT. The results show that both the cutting method and the time of cutting have an impact on the backsheet mechanical properties. Under UV exposure, Method II, age‐then‐cut, generally resulted in a higher average value, with more variation than Method I; however, if the side strips from Method II were excluded, the variation dropped to the same level. This is because the specimens at the sides of the sheet get additional damage from UV light from the exposed sides of the sample. In contrast to UV exposure, PCT specimens prepared by Method II result in lower average values and higher variability. This is attributed to embrittlement through the bulk of the sample where the cutting of embrittled specimens appears to result in more edge defects which can then initiate a break at smaller strains. The data suggest that for UV exposures, the specimens should be cut after aging and the exposed side specimens discarded, and that for PCT exposures, the specimens should be cut before the exposure.

Investigation on the Effect of Accumulated Charge-Induced Degradation on Multilayer Photovoltaic Insulating Backsheets Based on Atomic Force Microscopy

Lifetime Evaluation of Photovoltaic Polymeric Backsheets under Ultraviolet Radiation: From Chemical Properties to Mechanical Modeling

Material characterization of seven photovoltaic backsheets using seven accelerated test conditions

Degradation analysis of field-exposed photovoltaic modules with non-fluoropolymer-based backsheets

An Investigation on the Evolution of Insulation Performance of BOPP Films for Power Capacitors under Multi Physical Fields Aging

A Comparison of Emerging Nonfluoropolymer-Based Coextruded PV Backsheets to Industry-Benchmark Technologies

Aging behavior and degradation of different backsheets used in the field under various climates in China

Investigation of the Potential-Induced Aging Phenomenon of an Insulating Encapsulant for a Photovoltaic Module: From Electrical to Chemical Properties

Impact of specimen preparation method on photovoltaic backsheet degradation during accelerated aging test

Differential degradation patterns of photovoltaic backsheets at the array level

Evaluation of Surface Crack Formation in Photovoltaic Backsheets Using Fragmentation and Finite Element Simulations

Nondestructive Estimation of Strength Deterioration in Photovoltaic Backsheets Using a Portable Near Infrared Spectrometer

Reliability assessment on PV backsheets with and without considering spectral UV albedo effects: A theoretical comparison

Impact of environmental variables on the degradation of photovoltaic components and perspectives for the reliability assessment methodology

Comparison of Degradation Behavior of Newly Developed Encapsulation Materials for Photovoltaic Applications under Different Artificial Ageing Tests

Towards validation of combined-accelerated stress testing through failure analysis of polyamide-based photovoltaic backsheets

Physicochemical Characteristics and Dynamic Charge Mapping in Thermally Aged Two-Layered Polymer Considering Surface States: Experiment and Simulation

Development of Novel Frontsheets With Protective Coatings to Increase the Durability and Reliability of Glass‐Free Lightweight PV Modules

XPS analysis of damp heat aged and fractured polymer/glass laminates

Coupled In Situ Electrical and Optical Characterization to Assess the Accelerated Aging of Perovskite Solar Cells

Electric‐Induced Degradation of Cathode Interface Layer in PM7:IT‐4F Polymer Solar Cells