Abstract:Two different sequences are considered: Method (I) cut‐then‐age: cut into 1‐cm wide strips and then expose to stress, and Method (II) age‐then‐cut: expose a larger sheet to stress and then cut into 1‐cm widths for mechanical property measurements. The data suggest that for UV exposures, the specimens should be cut after aging and the exposed side specimens discarded, and that for pressure cooker test exposures, the specimens should be cut before the exposureIn this study, we highlight some important factors in the specimen preparation methods for evaluating photovoltaic backsheet properties after accelerated aging. Two different sequences are considered: Method (I) cut‐then‐age: cut into 1‐cm wide strips and then expose to stress, and Method (II) age‐then‐cut: expose a larger sheet to stress and then cut into 1‐cm widths for mechanical property measurements. We also compare the effect of three cutting methods, (a) tensile specimen punch, (b) paper cutter, and (c) fresh razor blade. Several commercial backsheets were evaluated, with stress exposures including (a) pressure cooker test (PCT), (b) dry ultraviolet (UV) radiation exposure, and (c) UV combined damp heat tests. Fourier transform infrared spectrometer (FTIR) and intrinsic viscosity (IV) were used to analyze the materials on unstressed materials and samples exposed to PCT. The results show that both the cutting method and the time of cutting have an impact on the backsheet mechanical properties. Under UV exposure, Method II, age‐then‐cut, generally resulted in a higher average value, with more variation than Method I; however, if the side strips from Method II were excluded, the variation dropped to the same level. This is because the specimens at the sides of the sheet get additional damage from UV light from the exposed sides of the sample. In contrast to UV exposure, PCT specimens prepared by Method II result in lower average values and higher variability. This is attributed to embrittlement through the bulk of the sample where the cutting of embrittled specimens appears to result in more edge defects which can then initiate a break at smaller strains. The data suggest that for UV exposures, the specimens should be cut after aging and the exposed side specimens discarded, and that for PCT exposures, the specimens should be cut before the exposure.

A Comparison of Emerging Nonfluoropolymer-Based Coextruded PV Backsheets to Industry-Benchmark Technologies

Material characterization of seven photovoltaic backsheets using seven accelerated test conditions

Degradation analysis of field-exposed photovoltaic modules with non-fluoropolymer-based backsheets

Aging behavior and degradation of different backsheets used in the field under various climates in China

Differential degradation patterns of photovoltaic backsheets at the array level

Investigation on the Effect of Accumulated Charge-Induced Degradation on Multilayer Photovoltaic Insulating Backsheets Based on Atomic Force Microscopy

Development of Novel Frontsheets With Protective Coatings to Increase the Durability and Reliability of Glass‐Free Lightweight PV Modules

Lifetime Evaluation of Photovoltaic Polymeric Backsheets under Ultraviolet Radiation: From Chemical Properties to Mechanical Modeling

Evaluation of Surface Crack Formation in Photovoltaic Backsheets Using Fragmentation and Finite Element Simulations

Impact of specimen preparation method on photovoltaic backsheet degradation during accelerated aging test

Properties and degradation behaviour of polyolefin encapsulants for photovoltaic modules

Comparison of Degradation Behavior of Newly Developed Encapsulation Materials for Photovoltaic Applications under Different Artificial Ageing Tests

Towards validation of combined-accelerated stress testing through failure analysis of polyamide-based photovoltaic backsheets

XPS analysis of damp heat aged and fractured polymer/glass laminates

Glass/glass photovoltaic module reliability and degradation: a review

Thermal Expansion Behavior of a Thermoplastic Polyolefin for Photovoltaic Application Over Hygrothermal Aging

Nondestructive Estimation of Strength Deterioration in Photovoltaic Backsheets Using a Portable Near Infrared Spectrometer

Repair and preventive maintenance of photovoltaic modules with degrading backsheets using flowable silicone sealant

Reliability assessment on PV backsheets with and without considering spectral UV albedo effects: A theoretical comparison

Enhancing photovoltaic modules encapsulation: Optimizing lamination processes for Polyolefin Elastomers (POE) through crosslinking behavior analysis

Extraction and analysis of back-sheet layer from waste silicon solar modules