Abstract:High strength-elongation synergy and its dependence on microstructure are the eternal themes of metallic materials including Ti alloys. In this study, the relationship between the microstructure evolution and mechanical properties of the Ti-25Zr-4Al-1.5Mn (TZAM, wt. %) near-α Ti alloy was systematically investigated after hot rolling at temperatures ranging in the whole solid solution region. The content of primary α phase decreased gradually with the increasing of rolling temperature. An excellent comprehensive mechanical properties with a yield strength of 1055±10 MPa and a total elongation of 23.6±0.6% were obtained for the specimen after rolling at 750 °C (single α phase temperature region). This great strength-elongation synergy is mainly due to the synthetic action of substructure strengthening, dislocation strengthening, basal random heterogeneity (BRH) texture, and suitable content of β phase. The α" martensitic phase was formed after rolling at temperatures of 800 and 850 °C (α + β two-phase temperature region), resulting in a significant decrease in yield strength. However, remarkable work hardening with a rate of approximately 10 GPa occurred in both specimens. The whole evolution process of primary α grains, namely dynamic recovery and recrystallization during hot-rolled is deeply discussed. When the rolling temperature increased to 900 °C (single β phase temperature region), the dominated acicular α´ martensitic phase with high dislocation density resulted in an ultra-high strength (1264±12 and 1488±11 MPa for yield and tensile strength respectively) at the expense of plasticity. These findings revealed the microstructure evolution and its relationship to the mechanical properties of a TiZr-based alloy after the thermomechanical processing and helped to understand deeply the theory of metallic strengthening and elongation.

ZrTiO4 secondary phase effects on ductility and toughness of molybdenum alloys

Effects of Zr Addition on the Deformation Behavior, Microstructure and Mechanical Properties of Dental Ti Alloys

Microstructure and Mechanical Properties of Unalloyed Molybdenum Fabricated Via Wire Arc Additive Manufacturing

Effect of secondary phases on the strength and elongation of a novel Mo-TiC-ZrC-C alloy

Evaluation of tensile property and strengthening mechanism of Zirconia reinforced molybdenum alloy

Secondary phases effects on microstructure and mechanical properties of lanthanum-doped titanium‐zirconium‐molybdenum alloy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Evaluating compressive property and hot deformation behavior of molybdenum alloy reinforced by nanoscale zirconia particles

Mechanical properties and corrosion behavior in molten zinc of Mo–ZrO 2 alloys

Optimization of Zr and Mo element on room-temperature fracture toughness and the integrity of oxide film

Correspondence of the aging behaviors and the phase constituents of the Ti-Mo-based alloys tailored by the Al and Zr additions

Effect of zirconia on low cycle fatigue and energy absorption of molybdenum alloy

Microstructure, mechanical properties and biocompatibility of novel Ti-20Zr-xMo alloys

Achieving an unprecedented strength-ductility balance of molybdenum alloy by homogeneously distributing yttrium-cerium oxide

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Enhanced ductility in hot compression tests by tailoring microstructure in the refractory high-entropy alloys MoNbTaTiV Zr

Effect of Zr on the as-cast microstructure and mechanical properties of lightweight Ti2VNbMoZrx refractory high-entropy alloys

Evaluating low cycle fatigue property of nanoscale ZrO2 particles strengthening molybdenum alloy

Effect of Molybdenum on the Impact Toughness of Heat-Affected Zone in High-Strength Low-Alloy Steel

Influence of Molybdenum on the Microstructure, Mechanical Properties and Corrosion Resistance of Ti20Ta20Nb20(ZrHf)20−xMox (Where: x = 0, 5, 10, 15, 20) High Entropy Alloys

Microstructure evolution and its effect on the impact toughness of the Ti-Al-V-Mo-Zr alloy tube