Abstract:The new developed metal/composite co-cured material composed of carbon fiber–reinforced plastic and Al phases has been increasingly applied for manufacturing of attitude control flywheel in aerospace industry. However, drilling of co-cured material is still a challenging task to produce holes with high quality and low cost in the assembly chain and dynamic balance debugging of attitude control flywheel. In other words, the relevant mechanisms and experimental findings involved in the drilling process of carbon fiber–reinforced plastic/Al co-cured material is not clearly defined, which impedes the progress of attitude control flywheel production. To this end, this article specially addresses the experimental studies on the drilling process of carbon fiber–reinforced plastic/Al co-cured material with standard TiAlN-coated cemented carbide twist drill. The significance of this work aims to reveal the regardful cutting responses of the hole characteristics and tool wear modes during the practical drilling process of co-cured material. A full factorial experiment including three levels of feed rate and four levels of cutting speed was performed. The hole diameter shows different values in different positions while it indicates consistent pattern regardless of the cutting variables: the largest in the Al phase, followed by the upper and lower carbon fiber–reinforced plastic phases, respectively. Grooves and matrix degradation are the major machining defects for carbon fiber–reinforced plastic layers, while a great chip debris adhered to the machined surface is the case for Al layer. Subsequent wear analysis showed that abrasion was mainly maintained at the vicinity of major/minor cutting edges and drill edge corner, followed by chip adhesion on the chisel edge region. Carbide substrate of drill flank face is exposed, and thereafter cavities are formed under the strong mechanical abrasion. These results could provide several implications for industrial manufacturers during the attitude control flywheel production.

Hole-exit defect formation during traditional and ultrasonic vibration-assisted drilling of C/SiC composites

Processing parameter effect, formation mechanism and inhibition method of micro-hole exit defects in rotary ultrasonic pecking drilling of SiC f /SiC composites

Drilling Induced Tearing Defects in Rotary Ultrasonic Machining of C/SiC Composites

Improving hole exit quality in rotary ultrasonic machining of ceramic matrix composites using a compound step-taper drill

Study on the surface integrity of micro-holes in high volume fraction SiCp/Al using ultrasonic vibration drilling

Material Removal Behavior of Ultrasonic Vibration Helical Grinding of SiCf/SiC Composites

Experimental Investigation of Ultrasonic Vibration Assisted Drilling of High Volume Fraction SiCp/Al

Experimental study on ultrasonic vibration–assisted drilling micro-hole of SiCf/SiC ceramic matrix composites

Study on formation mechanism of edge defects of high-volume fraction SiCp/Al composites by longitudinal-torsional ultrasonic vibration-assisted milling

Machining Performance Analysis of Rotary Ultrasonic-Assisted Drilling of SiCf/SiC Composites

Drilling process of Cf/SiC ceramic matrix composites: Cutting force modeling, machining quality and PCD tool wear analysis

Effects of tool vibration on fiber fracture in rotary ultrasonic machining of C/SiC ceramic matrix composites

Mechanical modeling of ultrasonic vibration helical grinding of SiCf/SiC composites

Hole characteristics and surface damage formation mechanisms of C /SiC composites machined by abrasive waterjet

Longitudinal amplitude effect on material removal mechanism of ultrasonic vibration-assisted milling 2.5D C/SiC composites

Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material

Femtosecond laser drilling of SiC/SiC composites in longitudinal magnetic field and semi-water immersion assistance

Research on Material Removal Mechanism of C/SiC Composites in Ultrasound Vibration-Assisted Grinding

Modeling and experimental analysis of ultrasonic vibration drilling force prediction model for tiny small holes in high body fraction aluminum-based silicon carbide composites

Effect of machining parameter on femtosecond laser drilling processing on SiC/SiC composites

Wear behavior and machining quality of novel high-sharp brazed diamond abrasive core drills during drilling SiCf/SiC composite micro-holes