Abstract:Due to its exceptional machinability, welding prowess, and resistance to corrosion, the lightweight 6061 Al–Mg–Si alloy finds extensive utilization within the realms of aerospace and transportation. Multi-directional forging process is a sever plastic deformation (SPD) process. In this investigation, a pristine 6061 industrial ingot was forged in multiple directions at 530 °C via four-upsetting and three-cross-stretching (4U3CS), seven-upsetting and six-cross-stretching (7U6CS), two different forging processes. T6 aging treatment is applied to the forged components after the pre-forging preparation. The investigation delved into the microstructural evolution during the process, alongside the mechanical performance across three orthogonal directions. The research findings underscore that, in comparison to 4U3CS, the cumulative deformation in 7U6CS fosters lattice distortion and defect formation, thereby promoting the dissolution of metastable phases and augmenting the driving force for precipitation during aging. Consequently, the tensile and yield strengths of the specimens increased by approximately 10 MPa across all three directions. Furthermore, 7U6CS retains a greater reservoir of deformation energy, acting as a catalyst for dynamic recrystallization, consequently, this process facilitates the enlargement of recrystallization nucleation regions and improves the degree of recrystallization uniformity. Following hot forging and subsequent T6 aging treatment, the disparity in grain size became more pronounced, diminishing from 418 to 208 μm. Coarse intergranular precipitates emerged as the primary origin of transgranular cracking. Post-T6 aging, the elongation rate of the specimens decreased across all three directions, accompanied by a substantial elevation in tensile and yield strengths. Notably, the mechanical performance of the 7U6CS-T6 specimen reached its zenith in the optimal direction, attaining values of 340 and 315 MPa for tensile strength and yield strength, respectively. Graphical

Tribological shifting phenomena during automatic multistage cold forging of an automotive Al6082-T6 steering yoke

Tribological performance of additive-manufactured aluminum alloy—effect of post-weld cold deformation

Microstructural evolutions and mechanical properties of 6082 aluminum alloy part produced by a solution-forging integrated process

Automatic Multi-Stage Cold Forging of an SUS304 Ball-Stud with a Hexagonal Hole at One End

Accurate Flow Characterization of A6082 for Precision Simulation of a Hot Metal Forming Process

Characterization of AZ31B, AZ61A and AZ80A magnesium alloys with an emphasis on temperature compensation for their application to a hot forging

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Microstructural Evolution and Mechanical Properties of 6082 Aluminum Alloy Automotive Rear Swing Arm Produced by Integrated Process

A modified Johnson-Cook model to determine plastic flow behavior of Fe-30Mn-9Al-0.8 C low-density steel during warm multiaxial forging

Effect of Cold Pressing Deformation on Microstructure and Residual Stress of 7050 Aluminum Alloy Die Forgings

Finite element analysis on axial-pushed incremental warm rolling process of spline shaft with 42CrMo steel and relevant improvement

Effect of Tooling Surface on Friction Conditions in Cold Forging of an Aluminum Alloy

Dynamic Deformation Mechanism for Distinct Flow Behaviors in FGH4113A Superalloy with High Γ′ Content During Isothermal Compression at Sub-/Near-/super-solvus Temperatures

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Effect of Multidirectional Forging on the Microstructures and Mechanical Properties of the Al–Mg–Si Alloy

Flow characteristics and hot workability of a typical low-alloy high-strength steel during multi-pass deformation

Flow softening and microstructural evolution of near β titanium alloy Ti-35421 during hot compression deformation in the α+β region

Research and Application of Precision Forging Forming Process for Flat Thin Flash of Automobile Disc Steering Knuckle

Study on Warm Forming Effects of the Axial-Pushed Incremental Rolling Process of Spline Shaft with 42crmo Steel

Effect of Variational Friction and Elastic Deformation of Die on Oscillating Cold Forging for Spline Shaft

Comprehensive study of hot compression behaviors and microstructure evolution of solutionized 6082 aluminum alloy extruded bar