Abstract:Abstract This paper describes the work conducted by the Canadian Nuclear Safety Commission (CNSC) related to the numerical simulations of reinforced concrete (RC) structures under deformable missile impact. The current paper is a continuation of the work conducted in the frame of the OECD/NEA* IRIS (Improving Robustness Assessment Methodologies for Structures Impacted by Missiles) Phase 3 benchmark project. The concrete mock-up with two simple structures attached, one welded and another bolted, was built and tested at the VTT Technical Research Centre in Espoo, Finland. This mock-up was impacted by three subsequent missiles with varying velocities in order to obtain the damage accumulation. To examine vibration transmission through the mock-up, the simple structures modelling equipment were attached to the rear wall of the structure, while the missile impact was at the centre of the front wall. The parameters of the missiles and the RC structure were selected to ensure a flexible behaviour of the RC target in the impact area with only moderate damages, specifically cracking and permanent deformation without perforation. The non-linear dynamic behaviour of the reinforced concrete slabs under missile impact was analyzed using the commercial FE code LS-DYNA. A hybrid FE model using both 3-D solid and 2-D shell FE models was developed for the target discretization. Since the ultimate objective of this work is to model the entire structure over long time periods, a simplified combined shell-solid model with distributed (smeared) reinforcement was selected and validated. This model employs solid FE around an impact area and shell FE for the rest of the mock-up. Detailed modelling of a large RC structure with all equipment attached leads to a very large finite element (FE) model. Therefore, two-level FE modelling using sub-modelling approach was employed: first, analyze the vibrations of a reinforced concrete structure with simplified equipment modelling, and second, analyze in detail the equipment connected to it. This approach assumes uncoupled dynamic behaviour of the structure and the equipment. While the sub-modelling technique is commonly used in static analysis, a special sensitivity analysis was conducted to prove the applicability of sub-modelling for impact analysis. Finally, the effect of structural damping was examined and the best possible damping was selected. The selected damping values and sub-models resulted in relatively good agreement with the test results for both global (RC mock-up) and local (equipment) behaviour.

An efficient numerical modeling approach for coupled electrical cabinets in nuclear power plants

Simplified Approach for Seismic Risk Assessment of Cabinet Facility in Nuclear Power Plants Based on Cumulative Absolute Velocity

Seismic response of cylinder assemblies in axial flow

Seismic Vulnerability of Cabinet Facility with Tuned Mass Dampers Subjected to High- and Low-Frequency Earthquakes

Efficient, Simulation of Power Distribution Network by Using Integral-Equation and Modal-Decoupling Technology

Evaluating the applicability of seismic retrofit of an electric cabinet in a power plant

Uncertainty Quantification of Seismic Response of Nuclear Reactor Building Using a Three‐dimensional Finite Element Model

Multiphysics-Coupled Modeling: Simulation of the Hydraulic-Operating Mechanism for A Sf6 High-Voltage Circuit Breaker

Nonlinear Time History Analysis of a Pre-Stressed Concrete Containment Vessel Model under Japan's March 11 Earthquake

Applicability of Sub-Modelling Technique for Dynamic Analysis of Concrete Structures With Attached Equipment Under Missile Impact

Solving coupled problems of lumped parameter models in a platform for severe accidents in nuclear reactors

Study on Ground Numerical Models for Floor Response Spectra Analysis of Nuclear Power Plant and Their Influences

Dynamic Structure-Soil-Structure-Interaction for Nuclear Power Plants

Comparative assessment of finite element macro-modelling approaches for seismic analysis of non-engineered masonry constructions

Experimental-based numerical simulation of interacting suspended ceiling-sprinkler piping systems

Research on approaches to automatic modeling of discrete ordinate programs based on CAD model

An Approach Inspired by Quantum Mechanics for the Modeling of Large Power Systems

Real-time simulations to enhance distributed on-line monitoring and fault detection in Pressurized Water Reactors

Modal Analysis and Seismic Response Evaluation on Structures of Advanced Pwr

Multidimensional Seismic Response Analysis of Large-Scale Steel-Reinforced Concrete Frame-Bent Structures in CAP1400 Nuclear Power Plant

Numerical simulation of typical abnormal operating conditions in the secondary circuit system of a Hua-long Pressurized Reactor nuclear power unit