Abstract:The absorber layers in perovskite solar cells possess a high concentration of mobile ion vacancies. These vacancies undertake thermally activated hops between neighboring lattice sites. The mobile vacancy concentration <math> N 0</math> is much higher and the activation energy <math> E A</math> for ion hops is much lower than is seen in most other semiconductors due to the inherent softness of perovskite materials. The timescale at which the internal electric field changes due to ion motion is determined by the vacancy diffusion coefficient <math> D v</math> and is similar to the timescale on which the external bias changes by a significant fraction of the open-circuit voltage at typical scan rates. Therefore, hysteresis is often observed in which the shape of the current–voltage, J–V, characteristic depends on the direction of the voltage sweep. There is also evidence that this defect migration plays a role in degradation. By employing a charge transport model of coupled ion-electron conduction in a perovskite solar cell, we show that <math> E A</math> for the ion species responsible for hysteresis can be obtained directly from measurements of the temperature variation of the scan-rate dependence of the short-circuit current and of the hysteresis factor <math> H</math>. This argument is validated by comparing <math> E A</math> deduced from measured J–V curves for four solar cell structures with density functional theory calculations. In two of these structures, the perovskite is <math> MAPbI 3</math>, where MA is methylammonium, <math> CH 3 NH 3</math>; the hole transport layer (HTL) is spiro (spiro-OMeTAD, 2,2<math> ′</math>,7,7<math> ′</math>- tetrakis[N,N-di(4-methoxyphenyl) amino]-9,9<math> ′</math>-spirobifluorene) and the electron transport layer (ETL) is <math> TiO 2</math> or <math> SnO 2</math>. For the third and fourth structures, the perovskite layer is <math> FAPbI 3</math>, where FA is formamidinium, <math> HC ( NH 2 ) 2</math>, or <math> MAPbBr 3</math>, and in both cases, the HTL is spiro and the ETL is <math> SnO 2</math>. For all four structures, the hole and electron extracting electrodes are Au and fluorine doped tin oxide, respectively. We also use our model to predict how the scan rate dependence of the power conversion efficiency varies with <math> E A</math>, <math> N 0</math>, and parameters determining free charge recombination.

Stability assessment of a planar perovskite solar cell: Estimating parasitic resistances using a new method

Long-Term Stability Analysis of 3D and 2D/3D Hybrid Perovskite Solar Cells Using Electrochemical Impedance Spectroscopy

Current-voltage curves of planar heterojunction perovskite solar cells - Novel expressions based on Lambert W function and Special Trans Function Theory

Investigating the effect of non-ideal conditions on the performance of a planar CH3NH3PbI3-based perovskite solar cell through SCAPS-1D simulation

Comprehensive Understanding of Heat-Induced Degradation of Triple-Cation Mixed Halide Perovskite for a Robust Solar Cell

Performance enhancement of a planar perovskite solar cell with a PCE of 19.29% utilizing MoS 2D material as a hole transport layer: a computational study

Vibration Analysis of Perovskite Solar Cells Resting on Porous Nanocomposite Substrate in Thermal Environment

Systematic derivation of a surface polarization model for planar perovskite solar cells

Influence of the Anode Buffer Layer Materials and the Light Radiation Power on the Efficiency of a Planar P-I-n Perovskite Solar Cell: Theory and Simulation

Real-Time Dynamic Observation of a Thermal and Electrical Coeffect on the Interfacial Evolution of Hybrid Perovskite Solar Cells by Electrochemical Impedance Spectroscopy

Experimental Validation of Optimized Solar Cell Capacitance Simulation for Rheology‐Modulated Carbon‐Based Hole Transport Layer‐Free Perovskite Solar Cell

Deducing transport properties of mobile vacancies from perovskite solar cell characteristics

Numerical Simulation of C-V and I-V Characteristics of Perovskite Based Solar Cells

Computational Study of Ternary Devices: Stable, Low-Cost, and Efficient Planar Perovskite Solar Cells

Thermal Analysis of a Plasmonic Perovskite Solar Cell: Using Coupled Opto-Electro-Thermal (OET) Modeling

A Study of Hysteresis in Perovskite Solar Cell

Degradation Analysis of Perovskite Solar Cells via Short-Circuit Impedance Spectroscopy: A case study on NiOx passivation

Study and Optimization of a New Perovskite Solar Cell Structure Based on the Two Absorber Materials Cs2TiBr6 and MASnBr3 Using SCAPS 1D

Revealing the Working Mechanisms of Planar Perovskite Solar Cells With Cross-Sectional Surface Potential Profiling

OPTIMIZATION OF THE PEROVSKITE SOLAR CELL STRUCTURE

Optimizing the performance of perovskite-based organic solar cells via graphene integration as the hole transport layer: a comprehensive analysis