Abstract:Some recent studies have highlighted the potential of adsorption technology for greenhouse gas CO2 capture from the flue gases. The pressure/vacuum swing adsorption (PSA/VPSA), temperature swing adsorption (TSA) and electrical swing adsorption (ESA) have attracted much research effort with the development of the novel CO2 adsorbents materials. Carbonaceous materials are the promising candidate adsorbents, since they have high BET surface area, better CO2 adsorption capacity and novel morphologies (monolith, bead, fiber). Moreover, these adsorbents materials are also unique to undergo direct-electrothermal regeneration. In this paper, carbonaceous materials with four morphologies (granular, monolith, fiber and bead) are used to capture CO2 from the flue gas. Activated carbon beads were made in our laboratory with 2000-3000 m2/g BET surface area and better electrical conductivity. The research contents include the adsorption equilibrium isotherms, breakthrough curves, electrical energy consumption at direct-electrothermal desortpion, and the optimization of the cycle adsorption/desorption processes. The experimental apparatus for the optimization of the cycle adsorption/Direct-electrothermal desorption process comprise an adsorber with 40-100mm height and 25-50mm diameter, an electricity heating unit, a cooling unit, a vacuum unit, a gas detection unit, a data acquisition and control system. The heating step by electricity is very fast, about 2-5 minutes to raise the temperature of adsorbents from 30°C to 150°C when using 50 V voltages. But the cooling step is very slow due to the poor heat conductivity of porous adsorbents, so the alternative cooling units are designed, one using the direct cooling unit with air or nitrogen passing through the column, the other one as the indirect cooling unit by the medium of water or heat transfer oil indirect cooling adsorbents. Three processes of the cycle adsorption/desorption to capture CO2 from the flue gases using carbonaceous materials are investigated, which included the conventional vacuum swing adsorption process, the electrical swing adsorption process, and the combined process of vacuum swing adsorption and direct-electrothermal regeneration. The mathematical models are proposed for different capture processes using activated carbons with four morphologies (granular, monolith, fiber, beads). Based on the experimental and theoretical investigations, the product recovery, purity, and the energy consumption of the adsorption processes for CO2 capture from the flue gas are compared, and the feasibilities of the capture processes using carbonaceous materials are evaluated comprehensively.

Carbon capture from humid gases using alkaline-promoted polypyrrole by a vacuum swing adsorption process

Polyethylenimine-Grafted Hkust-Type Mof/Poiyhipe Porous Composites (Pei@Pgd-H) As Highly Efficient Co(2 )Adsorbents

Design and development of 3D hierarchical ultra-microporous CO2-sieving carbon architectures for potential flow-through CO2 capture at typical practical flue gas temperatures

Engineering Porous Organic Polymers for Carbon Dioxide Capture

A Soluble and Recyclable Polymeric Adsorbent of Intrinsic Microporosity for CO2 Capture

Cost-effective carbon-based amine adsorbents for carbon capture: Equilibrium, kinetics and selectivity

Application of amine-loaded activated carbon fiber in CO2 capture and separation

Hierarchical Porous Carbon As a Highly Efficient Adsorbent for Toluene and Benzene

CO2 Adsorption by Polyamine-Based Protic Ionic Liquid-Functionalized Mesoporous Silica: Regenerability and Influence of Flue Gas Contaminants

Pyrrolic N-enriched Carbon Fabricated from Dopamine-Melamine Via Fast Mechanochemical Copolymerization for Highly Selective Separation of CO2 from CO2/N2

Carbon dioxide capture by adsorption of carbonaceous materials with direct-electrothermal desorption

A robust triphenylamine-based monolithic polymer network for selective sieving of CO2 and PM from flue gas

Recent Progress on Porous Carbons for Carbon Capture

Capture of CO 2 from Flue Gas by Vacuum Pressure Swing Adsorption Using Activated Carbon Beads

Capture of Co 2 by Vacuum Swing Adsorption Process Using Activated Carbon Beads

Microporous Carbon Coated Zeolite Particles for Efficient Carbon Capture from Wet Flue Gas

Porous Adsorption Materials for Carbon Dioxide Capture in Industrial Flue Gas

A Sequential Flow Process of CO2 Capture and Conversion Using Cost-Effective Porous Organic Polymers

Efficient Capture of CO2 from Flue Gas at High Temperature by Tunable Polyamine-Based Hybrid Ionic Liquids

Porous Organic Polymers For Post-Combustion Carbon Capture

Construction of Ultramicropore-Enriched N-doped Carbons for CO2 Capture: Self-decomposition of Polyethyleneimine-Based Precursor to Promote Pore Formation and Surface Polarity