Abstract:The combination of plastic scintillators with Silicon Photo-Multipliers (SiPMs) is widely used for detecting radiation in high-energy astrophysics, particle physics, neutrino physics, or medical physics. An example of application for this kind of detectors are Compton polarimeters such as POLAR-2 or LEAP, for which a low-Z material is needed for the Compton effect to be dominant down to as low energy as possible. Such detectors aim to measure low energy Compton depositions which produce small amounts of optical light, and for which optimizing the instrumental optical properties consequently imperative. The light collection efficiency of such a device was studied with a focus on the POLAR-2 GRB polarimeter, in which the conversion of incoming $\gamma$-rays into readable signal goes through the production and collection of optical light, which was to be optimized both through measurements and simulations. The optical elements of the POLAR-2 polarimeter prototype module were optically characterized and an optical simulation based on Geant4 was developed to fully model its optical performances. The results from simulations were used to optimize the design and finally to verify its performance. The study resulted in a detector capable of measuring energy depositions of several keV. In addition an important finding of this work is the impact of the plastic scintillator surface roughness on the light collection. It was found that a plastic scintillator with a higher scintillation efficiency but made of a softer material, hence with a rougher surface, was not necessarily the best option to optimize the light collection. Furthermore, in order to optimize the optical crosstalk between different channels, a production technique for very thin ($\sim$150$~\mu$m) and reusable silicone-based optical coupling pads, which can be applied for other experiments, was developed.

Mechanism of Polishing for Polystyrene Based Scintillators

Scattering of Polishing Powder Wear Nanoparticles on Sludge Nanoparticles during the Polishing of Polymer Optical Materials

Deposition and Localization of Polishing Powder Wear Nanoparticles on the Processed Surface of Polymeric Optical Materials

Quantum Mechanism of Optical Glass Polishing

Ultra-precise surface processing of LYSO scintillator crystals for Positron Emission Tomography

Polishing behavior of PS/SiO<sub>2</sub> Core-Shell nanoparticles with different shell thickness on fused silica Chemical Mechanical Polishing

Influence of a Cross-Linker Agent on Mechanical and Other Properties of Polysiloxane Based Scintillators

Optimizing the light output of a plastic scintillator and SiPM based detector through optical characterization and simulation: A case study for POLAR-2

The effect of PPO concentration on the scintillation properties of a polystyrene based plastic scintillator

Polystyrene-Silica Composite Particles and Their Copper Chemical Mechanical Polishing Performances

[Fabrication and Surface-Enhanced Raman Scattering Research on Polystyrene Nanospheres Arrays].

Optimizing of the Colloidal Dispersity of Silica Nanoparticle Slurries for Chemical Mechanical Polishing

The Effect of Sodium Hexametaphosphate on the Dispersion and Polishing Performance of Lanthanum–Cerium-Based Slurry

Methods and Mechanistic Analysis of Improving the Dispersion of Nano Silica Colloidal Particles in Chemical Mechanical Polishing Slurries

Precision Polishing of the Mandrel for X-Ray Grazing Incidence Mirrors in the Einstein Probe

Finishing of structured surfaces by abrasive polishing

Material Removal Rate of 4H-Sic Polishing with Polystyrene/CeO2Core/shell Abrasives

NANO-POLISHING SUBSTRATES FOR OPTICS AND MICROELECTRONICS

The Synthesis and Assembly Mechanism of Micro/Nano-Sized Polystyrene Spheres and Their Application in Subwavelength Structures

The Deterioration Characteristics and Mechanism of Polishing Pads in Chemical Mechanical Polishing of Fused Silica

Degradation of Polystyrene on Silver Substrates during Surface-Enhanced Raman Scattering