Abstract:To popularize the complete replacement of natural sand with manufactured sand, a study was performed to determine the effect of adding polypropylene fibres (PPFs) to increase the bending strength and carbonization resistance of manufactured sand concrete (MSC). A 2 × 3 factorial design with the content and length of PPF as variables was used to establish a carbonization depth prediction model and a response surface model (RSM). The phase composition and microstructure of polypropylene-fibre-reinforced manufactured sand concrete (PPF-MSC) were analysed using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show the addition of PPF with different contents and lengths increases the bending strength of PPF-MSC to varying degrees, while reducing the carbonization depth and increasing the dynamic elastic modulus after 28 days of carbonization. The highest bending strength (6.12 MPa) and carbonization resistance of PPF-MSC are obtained by the addition of 1 kg/m3 of 12 mm PPF, while the carbonization depth and an increase in the dynamic elastic modulus after 28 days of carbonization are maintained at a minimum of 2.26% and 1.94 mm, respectively. A prediction model was established to obtain a formula for the PPF-MSC carbonization depth in terms of the content and length of PPF and the carbonization time. The following results were obtained from the RSM: compared to the PPF length, the PPF content has a larger impact on the PPF-MSC bending strength and a smaller impact on the PPF-MSC carbonization resistance; there is no significant interaction between the content and length of PPF; and the predicted and measured values are close, indicating that the model is highly reliable. A comparison of the XRD patterns and SEM micrographs of PPF-MSC and MSC after 28 days of carbonization show a lower peak intensity of CaCO3 in the pattern for the carbonized area for PPF-MSC than for MSC and considerably fewer surface pores and cracks in PPF-MSC than in MSC. These results indicate that the addition of PPF increases the compactness of MSC and creates an effective resistance to the erosion by water molecules and carbon dioxide (CO2), thus enhancing the bending strength and carbonization resistance of MSC.

Reinforcement mechanism of nano-SiO 2 and polypropylene fibers on concrete abrasion resistance subject to dynamic sandy water

Effects of Natural Seawater and Sea Sand on the Compressive Behaviour of Unconfined and Carbon Fibre-Reinforced Polymer-Confined Concrete

Strength and Early Crack Resistance Experiment of Polypropylene Fiber Reinforced Concrete with Silicon Powder

Shear Fatigue Behavior of Reinforced Concrete Beams Produced with Manufactured Sand As Alternatives for Natural Sand

Experimental study on strength and abrasion-resistance enhancement admixture

Bonding behavior of concrete matrix and alkali-activated mortar incorporating nano-SiO2 and polyvinyl alcohol fiber: Theoretical analysis and prediction model

Predicting abrasion resistance of concrete containing plastic waste, fly ash, and graphene nanoplatelets using an artificial neural network and response surface methodology

Salt-Frost Damage and Life Prediction of Nano-SiO2 Polypropylene Fiber Aeolian Sand Concrete

Study and Microanalysis on the Effect of the Addition of Polypropylene Fibres on the Bending Strength and Carbonization Resistance of Manufactured Sand Concrete

Influence of Nano-SiO2 on the Mechanical Properties of Recycled Aggregate Concrete with and without Polyvinyl Alcohol (PVA) Fiber

Study of the influence of seawater and sea sand on the mechanical and microstructural properties of concrete

Gray Relation Analysis in Influential Factors of Abrasion Resistance of Pavement Manufactured Sand Cement Concrete

Experimental evaluation of mechanical properties and microstructure for recycled aggregate concrete collaboratively modified with nano-silica and mixed fibers

Effects of Aggregate Micro Fines (AMF), Aluminum Sulfate and Polypropylene Fiber (PPF) on Properties of Machine-Made Sand Concrete

Nano-SiO2 Recycled Concrete Anti-Sulfate Performance and Damage Mechanism Research

Effect of Nanosilica and Fiber on Mechanical Properties and Microstructure of Recycled Coarse Aggregates Road Concrete

Effect of Nanosilica on the Strength and Durability of Cold-Bonded Fly Ash Aggregate Concrete

Effects of Polypropylene Fibers on the Frost Resistance of Natural Sand Concrete and Machine-Made Sand Concrete

Mechanism of Interface Performance Enhancement of Nano-Sio2 Modified Polyvinyl Alcohol Fiber Reinforced Geopolymer Concrete: Experiments, Microscopic Characterization, and Molecular Simulation