Abstract:In order to implement numerical simulation of the thermal-mechanical behaviors in the nuclear fuel rods, a three-dimensional finite element model is established. The thermal-mechanical behaviors at the initial stage of burnup in both the pellet and the cladding are obtained. Comparison of the obtained numerical results with those from experiments validates the developed finite element model. The effects of the constraint conditions, several operation and structural parameters on the thermal-mechanical performances of the fuel rod are investigated. The research results indicate that: (1) with increasing the heat generation rates from 0.15 to 0.6 W/mm(3), the maximum temperature within the pellet increases by 99.3% and the maximum radial displacement at the outer surface of the pellet increases by 94.3%. And the maximum Mises stresses in the cladding all increase; while the maximum values of the first principal stresses within the pellet decrease as a whole; (2) with increasing the heat transfer coefficients between the cladding and the coolant, the internal temperatures reduce and the temperature gradient remains similar; when the heat transfer coefficient is lower than a critical value, the temperature change is sensitive to the heat transfer coefficient. The maximum temperature increases only 7.13% when h changes from 0.5 W/mm(2) K to 0.01 W/mm(2) K, while increases up to 54.7% when h decreases from 0.01 W/mm(2) K to 0.005 W/mm(2) K; (3) the initial gap sizes between the pellet and the cladding significantly affect the thermal-mechanical behaviors in the fuel rod; when the gap size varies from 0.03 mm to 0.1 mm, the highest temperature in the pellet increases by 19.7%, and the maximum first principal stress at the outer pellet surface decreases by 17.4%; it is critical to optimize the gap size in order to reduce the pellet-cladding mechanical interaction and avoid their contact at early stage. This study lays a foundation for the further research on the irradiation-induced mechanical behaviors in the fuel rods. (C) 2011 Elsevier Ltd. All rights reserved.

Thermal-Mechanical performance analysis of a petal-shaped fuel rod under RIA condition

Preliminary Analysis on the Thermal-Mechanical Behavior of Dispersed Plate-Type Fuel under Reactivity Insertion Accident

A study on the fracture pattern change of high-burnup fuel cladding failed by pellet-cladding mechanical interaction failure under reactivity-initiated accident conditions

Numerical simulation of mechanical interaction between pellet and zircaloy-4 cladding under reactivity-initiated accident conditions

Investigation of Plate Fuel Performance under Reactivity Initiated Accidents with Developed Multi-Dimensional Coupled Method

Thermomechanical Assessment of Fuel Rod Cladding Made of Zirconium Alloy and Silicon Carbide Material During Reactivity-Initiated Accident

Development of Mechanistic Cladding Rupture Model for Severe Accident Analysis and Application in PHEBUS FPT3 Experiment

Three-dimensional FE analysis of the thermal-mechanical behaviors in the nuclear fuel rods

3-Dimensional Multiphysics Modeling of Behaviors of Pressurized Water Reactor Fuel Rods With Missing Pellet Surface

Analysis on Pellet-Cladding Interaction of Fuel Rod During Power Ramp of NHR200-II

Thermal and Mechanics Analysis Code of the PWR Nuclear Fuel Performance Based on FEM

Development of Mechanistic Cladding Rupture Model for Integrated Severe Accident Code ISAA. Part I: Module Verification and Application in CAP1400

Development of a Transient Module Based on FROBA-ROD Code and Assessment for Fuel Rod Performance under Reactivity-Initiated Accident

Steady-State Performance Analysis of a Dual-Cladding Design for Accident Tolerance Fuel

International fuel performance study of fresh fuel experiments for PCMI effects during RIA experiments

Potential Impact of Accident Tolerant Fuel Cladding Critical Heat Flux Characteristics on the High Temperature Phase of Reactivity Initiated Accidents

Preliminary Prediction for Survival Time of Fuel Rod under Critical Heat Flux

Finite element based fuel performance investigation of U3Si2-FeCrAl design under normal and RIA conditions

Experimental and Numerical Study on the Oxidation and Melting Behaviors of Annular Fuel Rod under High Temperature Steam Condition

Preliminary Thermal-Mechanical Coupled Modeling of U-10Mo Helical Cruciform Fuel Rods under the Unirradiated and Irradiated Conditions

Thermomechanical Modeling of Pellet-Cladding Interaction Using State-Based Peridynamics