Abstract:Wire-based laser directed energy deposition (LDED) technology is an attractive and efficient additive manufacturing technology, which shows great potential in the process of manufacturing high-value engineering components. However, the thermal effect will lead to a large amount of residual tensile stress in the components, and the large crystal structures after solidification seriously affects the tensile performance. The pursuit of high mechanical properties in additive manufacturing components have prompted researchers to seek new strengthening process to produce high-strength components. Therefore, in this paper, laser shock peening (LSP) composite wire-based LDED were used for the additive manufacturing of 17-4 PH stainless steel under the specified experimental conditions, and the effects of LSP on microstructure evolution, microhardness, and tensile properties of wire-based LDED components were systematically studied. Results showed that uniform grains with an average size of 2.31 mu m were generated on the top surface of specimen due to the ultra-high plastic strain induced by LSP shock wave. The size of hierarchical martensitic units shows varying degrees of reduction after LSP treatment, which is shown by the width decrease of packet, block and lath. Dynamic recrystallization caused by rearrangement and annihilation of high-density dislocations promoted the grain refinement. Meanwhile, the residual stress was completely converted from tensile state into compressive state with a maximum value of 425 MPa, and the microhardness was also enhanced to a peak value of 432 HV. In addition, we observed that the high-density dislocation environment created by LSP treatment promoted the further precipitation, and the aggregation phenomenon of precipitates was observed in the dense dislocation area. Furthermore, the tensile strength and elongation of LSP treated specimen were improved significantly, which was attributed to the combined effects of grain refinement, introduction of dislocation structures, precipitation strengthening and gradient residual compressive stress. In summary, laser hybrid additive manufacturing technology provides a new idea and method for the production of high-performance precipitation hardening stainless steel components.

Influence of powder particle size distribution on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by selective laser melting

Microstructural and Mechanical Characterization of Selective Laser Melted 17-4 PH Stainless Steel: Effect of Laser Scan Strategy and Heat Treatment

Effect of heat treatment on microstructure and mechanical properties of 17-4PH stainless steel manufactured by laser-powder bed fusion

Effect of powder chemical composition on the as-built microstructure of 17-4 PH stainless steel processed by selective laser melting

Tailoring microstructure and mechanical properties of 17-4PH steel fabricated by wire-arc directed energy deposition via a combination of intrinsic and post-processing heat treatments

Effect of Process Parameters on Density and Mechanical Behaviour of a Selective Laser Melted 17-4PH Stainless Steel Alloy

The effects of particle size distribution on the rheological properties of the powder and the mechanical properties of additively manufactured 17-4 PH stainless steel

Tensile Properties and Microstructural Evolution of 17–4 PH Stainless Steel Fabricated by Laser Hybrid Additive Manufacturing Technology

Effect of hot isostatic pressing on the microstructure and mechanical properties of 17-4PH stainless steel parts fabricated by selective laser melting

Effect of homogenization on precipitation behavior and strengthening of 17-4PH stainless steel fabricated using laser powder bed fusion

Mechnical properties of 17-4PH stainless-steel at various laser sintering process parameters

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Characterization of Microstructural Anisotropy in 17–4 PH Stainless Steel Fabricated by DMLS Additive Manufacturing and Laser Shot Peening

Influence of Aging Treatment Regimes on Microstructure and Mechanical Properties of Selective Laser Melted 17-4 PH Steel

Microstructural, Mechanical, and Electrochemical Corrosion Properties of Extrusion Additive Manufactured 17-4 Precipitation Hardenable Stainless Steel

Homogenization timing effect on microstructure and precipitation strengthening of 17–4PH stainless steel fabricated by laser powder bed fusion

Influence of Sintering Atmosphere, Temperature and the Solution-Annealing Treatment on the Properties of Precipitation-Hardening Sintered 17-4 PH Stainless Steel

Structural and micromechanical properties of 316L stainless steel produced by selective laser melting

Microstructure–Hardness–Corrosion Performance of 17–4 Precipitation Hardening Stainless Steels Processed by Selective Laser Melting in Comparison with Commercial Alloy

Effect of heat treatment parameters on microstructure and microhardness of 15-5PH stainless steel fabricated by selective laser melting

Tailoring the Microstructural and Mechanical Properties of 316L Stainless Steel Manufactured by Laser Powder Bed Fusion