Abstract:Over the last decade, researchers have developed a variety of new analytical and clinical diagnostic devices. These devices are predominantly based on microfluidic technologies, where biological samples can be processed and manipulated for the collection and detection of important biomolecules. Polydimethylsiloxane (PDMS) is the most commonly used material in the fabrication of these microfluidic devices. However, it has a hydrophobic nature (contact angle with water of 110°), leading to poor wetting behavior and issues related to the mixing of fluids, difficulties in obtaining uniform coatings, and reduced efficiency in processes such as plasma separation and molecule detection (protein adsorption). This work aimed to consider the fabrication aspects of PDMS microfluidic devices for biological applications, such as surface modification methods. Therefore, we studied and characterized two methods for obtaining hydrophilic PDMS surfaces: surface modification by bulk mixture and the surface immersion method. To modify the PDMS surface properties, three different surfactants were used in both methods (Pluronic® F127, polyethylene glycol (PEG), and polyethylene oxide (PEO)) at different percentages. Water contact angle (WCA) measurements were performed to evaluate the surface wettability. Additionally, capillary flow studies were performed with microchannel molds, which were produced using stereolithography combined with PDMS double casting and replica molding procedures. A PDMS microfluidic device for blood plasma separation was also fabricated by soft lithography with PDMS modified by PEO surfactant at 2.5% (v/v), which proved to be the best method for making the PDMS hydrophilic, as the WCA was lower than 50° for several days without compromising the PDMS's optical properties. Thus, this study indicates that PDMS surface modification shows great potential for enhancing blood plasma separation efficiency in microfluidic devices, as it facilitates fluid flow, reduces cell aggregations and the trapping of air bubbles, and achieves higher levels of sample purity.

Reliable plasmonic biosensing with atmospheric pressure dielectric barrier discharge oxygen plasma treated polydimethylsiloxane microfluidic channels

Preparation and Properties of a Ph-Responsive PDMS Platform

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

Study of plasma treatment for PDMS surface modification on the fabrication of microfluidic devices

The stability of radio-frequency plasma-treated polydimethylsiloxane surfaces

Polydimethylsiloxane Surface Modification of Microfluidic Devices for Blood Plasma Separation

Investigation of Cold Atmospheric Plasma Treatment in Polydimethylsiloxane Microfluidic Devices with a Transmural Method

Microscale investigation on the wettability and bonding mechanism of oxygen plasma-treated PDMS microfluidic chip

Hybrid Polystyrene-Plasmonic Systems as High Binding Density Biosensing Platforms

Surface modification of polydimethylsiloxane by the cataractous eye protein isolate

Atmospheric Pressure Plasma Functionalization of Sealed PDMS Microfluidics: Application to Capillary Pumping and Enhanced Cell Growth.

Improvement of PDMS surface biocompatibility is limited by the duration of oxygen plasma treatment

Recent developments in PDMS surface modification for microfluidic devices

Fabrication of a cost-effective polymer nanograting as a disposable plasmonic biosensor using nanoimprint lithography

Systematic Characterization of Hydrophilized Polydimethylsiloxane

Treatment of PDMS surfaces using pulsed DBD plasmas: comparing the use of different gases and its influence on adhesion

Bio-inspired wettability patterning for flexible and wearable electrochemical immunosensors utilizing PDMS-TiO 2 coating

Evaluation of polydimethylsiloxane (PDMS) surface modification approaches for microfluidic applications

Reagent‐Free Covalent Immobilization of Biomolecules in a Microfluidic Organ‐On‐A‐Chip

Localized Surface Hydrophilicity Tailoring of Polyimide Film for Flexible Electronics Manufacturing Using an Atmospheric Pressure Ar/H2O Microplasma Jet

PtOEP–PDMS-Based Optical Oxygen Sensor