Abstract:A modified nano-calcium carbonate (R-CCR) was prepared by coating a layer of unsaturated hydroxylfatty acid on the surface of CCR powders using a solid state method; the latter were commercial nano-CaCO 3 modified with stearic acid. FTIR studies indicate that the modifier is combined on the surface of CaCO 3 . PP/EPDM/nano-CaCO 3 ternary composites were prepared by a melt-mixing method. SEM and TEM were utilized to examine the morphology of the composites. The tensile fractured surface of PP/EPDM/R-CCR showed a fibroid morphology and large-scale yield deformation. The impact fractured surface showed that the amount of cavities in the PP/EPDM/R-CCR system was increased, however their size diminished obviously. R-CCR particles were dispersed uniformly in the PP matrix, and their compatibility was distinctly improved as compared to CCR when the amount of R-CCR was 15 h −1 . The tensile strength remained nearly constant (reduced from 27.6 MPa to 27.5 MPa), while the impact strength increased from 9.6 kJ/m 2 to 15.4 kJ/m 2 as CCR was replaced by R-CCR. Meanwhile, the bending strength and bending modulus also increased correspondingly. Furthermore, the impact strength of PP/EPDM/R-CCR was maintained at a high level (15.4 kJ/m 2 ), which was more than the sum of that of PP/EPDM and PP/R-CCR (6.6 kJ/m 2 and 6.1 kJ/m 2 respectively). This indicates that the R-CCR and EPDM have a significant synergistic toughening effect on PP while maintaining the strength and modulus of virgin PP. Both the storage modulus G′ and loss modulus G″ of PP/EPDM and PP/EPDM/R-CCR composites increase with increasing frequency, but the values of G′ and G″ of the tertiary composite are relatively higher than those of the binary system. The loss factor and viscosity decrease with increasing frequency, but there is little difference between tertiary and binary composites. The apparent viscosity η of the tertiary system containing R-CCR is lower than that of the tertiary system containing CCR and virgin PP. The viscosity of the composites sig-nificantly decreases with increasing shear rate. The mea-sured mechanical properties of the composites indicate that replacing CCR with R-CCR for binary composites could simultaneously enhance the toughness and strength of PP.

增容改性回收PP/废弃瓦楞纸粉复合材料的力学性能、形态和热行为

Enhancement on the properties of polypropylene using bamboo particles: Effect of particle sizes and loadings

Recycled Polypropylene/SEBS Polyblends: Manufacture and Mechanical Property Evaluation

Study on Properties of Modified Bamboo Fiber Reinforced Polypropylene Composites

Effects of reactive compatibilization on the morphological, thermal, mechanical, and rheological properties of intumescent flame-retardant polypropylene.

Combination of double-modified clay and polypropylene-graft-maleic anhydride for the simultaneously improved thermal and mechanical properties of polypropylene

Surface Modification of Shell Waste and Its Application in Polypropylene Composites

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Mechanical and thermal properties of polypropylene (PP) composites filled with modified shell waste

Carbon Fiber Reinforced Recycled Polypropylene/Polyolefin Elastomer Composites with High Mechanical Properties

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

Recycled polypropylene/crystalline cellulose composites obtained using polypropylene functionalized with maleinized hyperbranched polyol polyester as compatibilizing and plasticizing agent

Characteristics of paper mill sludge-wood fiber-high-density polyethylene composites

Preparation of Waste PP/Fly Ash/Waste Stone Powder Composites and Evaluation of Their Mechanical Properties

Enhancing Mechanical Performance of High-Lignin-Filled Polypropylene via Reactive Extrusion

Study on Properties of Wood Fiber Reinforced Polypropylene Composites

Compatibility study of recycled Polypropylene (PP)/Poly(ethylene terephthalate) (PET) blends nanocomposites with PP‐g‐MAH: Modeling of twin screw extrusion

Effect of Unsaturated Hydroxyl-Fatty Acid Modified Nano-Caco3 on the Morphological and Rheological Behavior of PP

A Promising Recycling Strategy via Processing Polypropylene/Recycled Poly(ethylene terephthalate): Reactive Extrusion Using Dual Compatibilizers

Towards a Circular Economy: Study of the Mechanical, Thermal, and Electrical Properties of Recycled Polypropylene and Their Composite Materials

Waste cotton stalks enhancing the impact and crystallization performances of polylactic acid/polypropylene composite with PP-g-mah compatibilizer