Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. The used ground coffee waste (GCW) and tea leaf waste (TLW), the large wastes from the beverage process, were selected as natural reinforcement and natural pigment in the polypropylene (PP) matrix. In this work, the maleic anhydride polypropylene (MAPP) was added to the composites to develop the compatibility between fillers, fibers, and polymer matrix. The TLW/PP composites, GCW/PP composites, and GCW/TLW/PP hybrid composites were prepared in the ratio of TLW and GCW ranging from 0 to 30 wt% with the addition of MAPP at 5 wt% of fillers. The presence of GCW and TLW in the PP matrix decreased tensile properties and impact resistance but increased flexural modulus and hardness of PP at high concentrations of GCW and TLW. The increase in GCW and TLW concentration slightly reduced melting temperature but it enhanced the tensile and flexural modulus. Furthermore, it enhanced the hardness, thermal and rheological properties of the composites. The TLW/PP composites had better mechanical properties, and rheological properties than GCW/PP composites but thermal properties were quite similar. The mechanical properties of GCW/TLW/PP hybrid composites were better than those of GCW/PP composites but lower than those of TLW/PP composites. The rheological and thermal behaviour of hybrid composites were like that of TLW/PP composites. Incorporating MAPP improves the mechanical and rheological behavior of PP composites by enhancing the interaction among PP, GCW, and TLW. However, this addition does not significantly enhance the composites' thermal properties. The optimum composite was hybrid composites of GCW/TLW/PP consisting of GCW of 10 wt%, TLW of 20 wt%, and MAPP of 1.5 wt% which presented good mechanical, thermal, and rheological properties. The mechanical properties of this hybrid composites were as follows: a tensile strength of 26.35 MPa, elongation at break of 10.91%, tensile modulus of 636.69 MPa, flexural strength of 45.57 MPa, flexural modulus of 3632.86 MPa, impact resistance of 12.72 kJ/m2, and a Shore D hardness of 76.15. The overall results showed that GCW and TLW can be used as reinforcement material and natural pigment in the polymer matrix.

Characteristics of paper mill sludge-wood fiber-high-density polyethylene composites

The potential of paper mill sludge for wood–plastic composites

Ultra-strong and environmentally friendly waste polyvinyl chloride/paper biocomposites

High-value utilization method of digital printing waste paper fibers-Co-blending filled HDPE composites and performance improvement

Effects of Natural Fiber Waste, Content, and Coupling Agent on the Physical and Mechanical Properties of Wood Species–Plastic Composites as Green Materials

Effect of wood flour and compatibilizer content on the properties of wood-plastic composites

Mechanical properties and water absorption behavior of injection-molded wood fiber/carbon fiber high-density polyethylene hybrid composites

Possibility of using municipal solid waste for manufacturing wood-plastic composites: effects of natural weathering, wood waste types, and contents

Some Exploitation Properties of Wood Plastic Hybrid Composites Based on Polypropylene and Plywood Production Waste

Sustainable composites from agricultural waste: The use of steam explosion and surface modification to potentialize the use of wheat straw fibers for wood plastic composite industry

Preparation and Characterisation of Sustainable Wood Plastic Composites Extracted from Municipal Solid Waste

Recycling Polyurethane Materials to Improve Properties of Wood Composite Panels

The Reinforcing Effect of Waste Polyester Fiber on Recycled Polyethylene

The Reinforcing Effect of Waste Corrugated Paper Fiber on Polylactic Acid

Effects of Wood Content and Modification on Properties of Wood Flour/Polybutylene Adipate Terephthalate Biocomposites

Preparation of wood plastic composite from flax fibers and post consumed polystyrene foam based on environmental and economical scales

Preparation of Waste PP/Fly Ash/Waste Stone Powder Composites and Evaluation of Their Mechanical Properties

Selected properties of MDF boards bonded with various fractions of recycled HDPE particles

Ecofriendly hybrid natural fiber reinforced polypropylene composites from biowastes

Synergistic reinforcing effect of fly ash and powdered wood chips on the properties of polypropylene hybrid composites

Compression molding of polypropylene‐ and polyethylene‐based composite materials using siliceous waste concrete powder