Abstract:In this paper, a novel hard nickel composite coatings were fabricated by wide-band laser cladding technique. The effects of Si alloying on the composite coatings were investigated by microstructure characterization, phase identification, microhardness and wear resistance. Results showed that the in-situ precipitated phases in the laser molten pool were composed of the γ-Ni solid solution and hard phases such as Cr 23 C 6 , CrSi, Cr 5 B 3 . With the increase of Si element, the morphology of the precipitated phases changed significantly. When the added content of Si was 1.0 wt.%, the precipitated phase was a mainly block morphology. As the added content of Si was increased to more than 2.0 wt.%, the main precipitated phase was transformed into a long stripe morphology. With the increase of Si content, the stripe-like precipitated phase was gradually refined and finally becomes density needle-like precipitates. Element distribution analysis showed that the block precipitated phase was enriched in Cr, W and Si elements. Additionally, the enriched elements in the long strip precipitation phase were essentially the same as those in the block precipitation phase. The added Si element was highly involved in the in-situ reactions of precipitated phase. The TEM results showed that the precipitated phases contained the crystal structures of Cr 5 B 3 and Cr 7 C 3 . The pin-on-disc wear tests revealed that the composite coating with the addition of 6 wt.% Si exhibited the best wear resistance in the experimental group. The average friction coefficient was about 0.6 and the wear mass loss rate was about 2.38 × 10 −5 g/m under counter-abrasive conditions. The worn surface analysis indicated that the wear mechanism of composite coatings was mainly abrasive wear. The refined needle-like precipitated phase was closely bound to the matrix and thus not easy to peel off, providing a significant improvement in the wear resistance of the laser cladding coatings.

Effects of reflectivity on laser-ablation resistance of the laser-cladding repaired Nd2O3 modified SiO2 coatings on C/C composites

Laser ablation behavior of SiO2-Nd2O3/Si-SiC-MoSi2 coated C/C composites repaired by laser cladding

Repair of SiC coating on carbon/carbon composites by laser cladding technique

Additively-manufactured multiphase coatings with laser protection ability for the repairing of MoSi2-SiC/SiC coated C/C composites

Design and preparation of composite coatings with increased reflectivity under high-energy continuous wave laser ablation

Effects of CeO2 on the Microstructure and Properties of Laser Cladding 316L Coating

Enhanced oxidation resistance of Mo-modified Si-SiC coating on C/C composites by laser-inducing

Toward improving the reflectivity of ablative heat-insulating coating under high-energy laser irradiation

Microstructures and Properties of Laser Cladding Al-TiC-CeO₂ Composite Coatings

Study on the laser ablation behavior of nitride coatings on carbon fiber epoxy resin composite

Microstructure and corrosion-wear behaviors for laser cladding repaired martensitic stainless steels using Co-based and Ni-based powders

The Effects of the Addition of Ti3SiC2 on the Microstructure and Properties of Laser Cladding Composite Coatings

Investigation on the Microstructure Evolution and Properties of a Novel In-Situ Fiber Phase-Reinforced Nickel Composite Coating Deposited by Wide-Band Laser

Ablation behavior of SiC whisker and ZrB2 particle-filled ZrO2 sol-gel composite coating under high-intensity continuous laser irradiation

Comparative investigation on microstructures and properties of WC/Cr 3 C 2 reinforced laser cladding Ni-based composite coatings subjected to ultrasonic impact treatment

Impact of laser-contaminant interaction on the performance of the protective capping layer of 1 ω high-reflection mirror coatings

Effect of SiC and TiC content on microstructure and wear behavior of Ni-based composite coating manufactured by laser cladding on Ti-6Al-4V

Laser ablation behavior and mechanism of Cf/C–SiC composites under different laser energy densities

Ablated surface morphology evolution of SiCp/Al composites irradiated by a nanosecond laser

The Effect of Laser Power on the Interface Microstructure of a Laser Remelting Nano-SiC Modified Fe-Based Ni/WC Composite Coating

Material migration and damage characteristics of fused silica optical surface treated by CO 2 laser/short – pulse ultraviolet laser