Abstract:This paper presents a comprehensive investigation of the effects of cutting parameters on the surface integrity of milled γ-TiAl alloys. Surface topography, surface roughness, surface defects, plastic deformation, micro-hardness, chip morphology, and tool wear of the milled γ-TiAl alloys were analyzed. The results indicate that the feed rate had the greatest influence on the surface topography and surface roughness. The value of surface roughness increased with the increase in cutting depth and feed rate. However, with the increase in cutting speed, it initially increased and then decreased. The minimum surface roughness was found to be 0.066 μm. The thickness of the plastic deformation layer and the micro-hardness value increased with the increase in cutting depth and feed rate. Also, they initially increased and then decreased with the increase in cutting speed. The minimum thickness of the plastic deformation layer was 15 μm and the depth of the hardened layer on the processed surface varied between 55 and 70 μm. The chip morphology was closely related to the quality of the processed surface. When the cutting depth and feed rate decreased, the chip morphology was transformed from segmented to nearly smooth. When the cutting depth and feed rate reached a critical point, plastic processing of γ-TiAl was achieved. Compared to brittle deformation, a more favorable processed surface was obtained. Finally, the comparison tests of tool wear were carried out with dry and flood coolant cutting. When the cutting speed reached 120 m/min in dry cutting, the tool life was very poor, and the cutting distance was only 1 m. However, the tool life was generally good when cutting with low cutting speed under the following conditions: vc = 60 m/min, ap = 0.1 mm, and fz = 0.01 mm/tooth. Under these conditions, the cutting distance was 60 m in dry cutting with the tool wear of 0.2 mm and 120 m in flood coolant cutting with the tool wear of 0.1 mm. The tool life in flood coolant operation was better than that of dry operation. The tool life decreased to 30 m when cutting with high cutting speed or feed rate (ap = 0.25 mm or fz = 0.025 mm/tooth).

Study of chip adhesion behavior in titanium alloy dry milling process based on image extraction technology

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Investigation of Chip Formation Mechanism and Surface Integrity in High Speed Milling Titanium Alloy

Adhesion Wear on Tool Rake and Flank Faces in Dry Cutting of Ti-6al-4v

Effect of cutting conditions on the serrated chip formation in high-speed cutting

High Speed Milling Titanium Alloy With Respect To Cutting Tooth Number

A Study on the Influence of Milling Parameters on the Properties of TC18 Titanium Alloy

The Taguchi orthogonal analysis of Ti6Al4V titanium alloy chip morphology in micro-milling

Experimental study of wet and dry milling effect on surface roughness of TC4 titanium alloy

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling

Study of surface integrity of milled gamma titanium aluminide

Experimental Study on the Optimization of Ti1023 Milling Parameters

Investigation of Cutting Force in High Feed Milling of Ti6al4v

Study on Mechanical Properties of Titanium Alloy with Micro-Texture Ball-End Milling Cutter under Different Cutting Edges

Performance of carbide tools with micro-texture on titanium alloys cutting in dry conditions

3D surface topography analysis and functionality-related performance of the machined surface in slot micro-milling titanium alloy Ti6Al4V

Chip Formation in High-Speed Milling of Titanium Alloy with PCD Tools

Cutting Responses of Additive Manufactured Ti6Al4V with Solid Ceramic Tool under Dry High-Speed Milling Processes

Experimental study on fracture mechanism transformation in chip segmentation of Ti-6Al-4V alloys during high-speed machining

Effect of Surface-Textured AlSiTiN Coating Parameters on the Performance of Ball-End Milling Cutter in Titanium Alloy Milling