Abstract:Background: The goal of this in vitro study was to compare three different surfaces: two types of implant surfaces commercially available ([a] smooth/machined and [b] acid-treated surface) versus (c) anodized surface. Discs were manufactured with commercially pure titanium (CP) grade IV, which were subsequently analyzed by scanning microscopy and fibroblastic and osteoblastic cell cultures. Methods: Ninety-nine discs (5 × 2 mm) were manufactured in titanium grade IV and received different surface treatments: (i) Mach group: machined; (ii) AA group: double acid etch; and (iii) AN group: anodizing treatment. Three discs from each group were analyzed by Scanning Electron Microscopy (SEM) to obtain surface topography images and qualitatively analyzed by EDS. Balb/c 3T3 fibroblasts and pre-osteoblastic cells (MC3T3-E1 lineage) were used to investigate each group's biological response (n = 10/cellular type). The data were compared statistically using the ANOVA one-way test, considered as a statistically significant difference p < 0.05. Results: The AA group had numerous micropores with diameters between 5 and 10 μm, while nanopores between 1 and 5 nm were measured in the AN group. The EDX spectrum showed a high titanium concentration in all the analyzed samples. The contact angle and wetting tension were higher in the AA, whereas similar results were observed for the other groups. A lower result was observed for base width in the AA, which was higher in the other two groups. The AN showed the best values in the fibroblast cells, followed by Mach and AA; whereas, in the culture of the MC3T3 cells, the result was precisely the opposite (AA > Mach > AN). There was similar behavior for cell adhesion for the test groups (Mach and AN), with greater adhesion of Balb/c 3T3 fibroblasts compared to MC3T3 cells; in the AA group, there was greater adherence for MC3T3 cells compared to Balb/c 3T3 fibroblasts. Conclusions: The findings suggest that different surface characteristics can produce different biological responses, possibly cell-line dependent. These findings have important implications for the design of implantable medical devices, where the surface characteristics can significantly impact its biocompatibility.

In-Vitro Comparison of Titanium Disc Surface Roughness and Bacterial Colonization after Ultrasonic Instrumentation with Three Different Tips

Assessing the Impact of Various Decontamination Instruments on Titanium and Zirconia Dental Implants: An In Vitro Study

Ultrasonic Instrument Effects on Different Implant Surfaces: Profilometry, Energy-Dispersive X-ray Spectroscopy, and Microbiology In Vitro Study

Cell Response of Titanium Implant with a Roughened Surface Containing Titanium Hydride: an in Vitro Study

The Effects of Ultrasonic Scaling and Air-Abrasive Powders on the Topography of Implant Surfaces: Scanning Electron Analysis and In Vitro Study

Influence of eight debridement techniques on three different titanium surfaces: A laboratory study

Fibroblasts and osteoblasts behavior after contact with different titanium surfaces used as implant abutment: An in vitro experimental study

Bacterial adhesion on smooth and rough titanium surfaces after treatment with different instruments

In vitro evaluation of chemical decontamination of titanium discs

Evaluation of the surface alterations and the adhesion strength of human periodontal ligament cells on titanium surface treated by pure titanium and conventional ultrasonic scaler tips

Comparison of antimicrobial effect of several decontaminating methods on contaminated Titanium discs

The Impact of Mechanical Debridement Techniques on Titanium Implant Surfaces: A Comparison of Sandblasted, Acid-Etched, and Femtosecond Laser-Treated Surfaces

Effects of Surface Conditions of Titanium Dental Implants on Bacterial Adhesion

Confocal Laser Scanning Microscope Evaluation of Early Bacterial Colonization on Zirconium Oxide and Titanium Surfaces: an in Vivo Study

Efficacy of Combined Mechanical and Chemical Decontamination Treatments on Smooth and Rough Titanium Surfaces and Their Effects on Osteoconduction: An Ex Vivo Study

Blood Wettability of Different Dental Implant Surfaces after Different Pre-Treatments: Ultrasonic Instrumentation, Platelet-Rich Fibrin Coating, and Acid Etching. An In Vitro Study

Influence of Dental Titanium Implants with Different Surface Treatments Using Femtosecond and Nanosecond Lasers on Biofilm Formation

Comparative analysis of the physical, chemical, and microbiological properties of Ti-6Al-4V disks produced by different methods and subjected to surface treatments

Plaque formation on surface modified dental implants. An in vitro study

In Vitro Study of the Proliferation of MG63 Cells Cultured on Five Different Titanium Surfaces

[Observation of Topography and Analysis of Surface Contamination of Titanium Implant after Roughness Treatment].