Abstract:Over the last 20 years, flue gas desulfurization gypsum (FGD gypsum) has become a valuable and widely used substitute for a natural raw material to produce plasters, mortars, and many other construction products. The essential advantages of FGD gypsum include its high purity and stability, which allow for better technical parameters compared to natural gypsum, and, until recently, its low price and easy availability. This FGD gypsum is obtained in the process of desulfurization of flue gases and waste gases in power plants, thermal power plants, refineries, etc., using fossil fuels such as coal or oil. The gradual reduction in energy production from fossil raw materials implemented by European Union countries until its complete cessation in 2049 in favor of renewable energy sources significantly affects the availability of synthetic gypsum, and forces producers of mortars and other construction products to look for new solutions. The gypsum content in commonly used light plaster mortars is usually from 50 to 60% by mass. This work presents the results of tests on mortars wherein the authors reduced the amount of gypsum to 30%, and, to meet the strength requirements specified in the EN 13279-1:2008 standard, added Portland cement in the amount of 6–12% by mass. Such a significant reduction in the content of synthetic gypsum will reduce this raw material's consumption, thus extending its availability and developing other solutions. The study presented the test results on strength, density, porosity, pore size distribution, and changes in the microstructure of mortars during up to 180 days of maturation in conditions of increased relative humidity. The results show that decreased porosity and increased mechanical strength occur due to the densification of the microstructure caused by the formation of hydration products, such as C-S-H, ettringite, and thaumasite.

Strength and water absorption for gypsum—cement—silica fume blends of improved performance

Gypsum hemihydrate–cement blends to improve renderings durability

High-strength gypsum binder with improved water-resistance coefficient derived from industrial wastes

Effect of gypsum on hydration properties, composition and kinetics of low carbon belite-ye'elimite-Q phase-ferrite clinker

A Study of the Influence of Cement Addition and Humidity on the Mechanical Strength and Microstructure of Flue Gas Desulfurization Gypsum–Cement Plasters

Effects of Different Admixtures on the Mechanical and Thermal Insulation Properties of Desulfurization Gypsum-Based Composites

Strength and Durability Studies on Hybrid Fiber Reinforced High-Performance Concrete for Silica Fume Based Mineral Admixture

Investigation of self-compacting concrete utilizing different supplementary pozzolanic materials for cement replacement

Effects of Percentages and Effective Cementitious Coefficient of Zeolite and Silica Fume on the Compressive Strength and Water Absorption of Concrete

Effect of Mineral Admixtures on Physical, Mechanical, and Microstructural Properties of Flue Gas Desulfurization Gypsum-Based Self-Leveling Mortar

Effect of Adding Silica Fume, Calcium Carbonate or Silicon Carbide on the Properties of an Alternative Binder Based on Anhydrite and Blast Furnace Slag

Use of recycled gypsum in the cement-based stabilization of very soft clays and its micro-mechanism

Optimization of mechanical properties and water absorption behavior of building gypsum by ternary matrix mixture

Effect of Silica Fume on the Rheological Properties of Cement Paste with Ultra-Low Water Binder Ratio

Concrete Mix Strength and Permeability with Various Supplementary Cementitious Materials

Influence of Calcined Flue Gas Desulfurization Gypsum and Calcium Aluminate on the Strength and AFt Evolution of Fly Ash Blended Concrete under Steam Curing

Development of lime-pozzolan green binder: The influence of anhydrous gypsum and high ambient temperature curing

Effect of sodium sulfate and gypsum on performances of expansive grouting material with aluminum as expansion agent

Relationship Between Microscopic Pore Structure and Strength of Cement-Based Materials with Low Water-Binder Ratio Under Sulfate Attack Environment

Properties of CO 2 -cured cement incorporating fly ash and slag subjected to further water curing

Workability and mechanical properties of ultrafine cement based grout for structural rehabilitation: A parametric study on the partial replacement with SCMs