Abstract:Journal of Composite Materials, Ahead of Print. During the last decades, environmental concerns and limited resources have set focus of research on lightweight, mechanically high-performing structures for the transportation industry, in order to reduce fuel consumptions and CO2 emissions. Friction Stir Joining (FSJ), as a variant of the Friction Stir Welding (FSW), is an innovative friction-based joining technique for metal-composite hybrid structures. Joining in the plasticized state below the melting temperature of the metal leads to a comparatively small heat-affected zone, so that only minor metallurgical changes occur. Additionally, only a short processing time and no additional weight in form of fasteners is needed. The main objective of this study is to evaluate the feasibility of metal-composite structures via FSJ, intending to enable a macro-mechanical interlocking bonding mechanism. Main focus was given to the integration of an aluminium nub inserted in a carbon fiber-reinforced polyphenylene sulfide (CF-PPS) sheet, to ensure sufficient plasticization of the aluminium part and no degradation in the polymer part. Residual stress arising from the friction stir joining process was also characterised using the Contour method. In this study, aluminium alloy 6082-T6 and CF-PPS composite sheets were used to produce long lap joints. Results have shown that the joints were created at almost constant peak temperature slightly above the melting temperature of the PPS but no physical-chemical changes were detected in the PPS. In addition, the influence of a PPS film as interlayer between the sheets was investigated in order to explore a method for preventing galvanic corrosion. Preliminary results indicate that it is not possible to integrate a metal nub to the CF-PPS without interrupting the PPS film. However, it is possible to create a nub within the PPS film.

Influence of metal surface structures on composite formation during polymer‐metal‐joining based on reactive Al/Ni multilayer foil

Effect of Metal Surface Topography on the Interlaminar Shear and Tensile Strength of Aluminum/Polyamide 6 Polymer-Metal-Hybrids

Effects of Physical Properties of Components on Reactive Nanolayer Joining

Development and Analysis of a New Joining Method for Polymer-Metal Hybrid Structures

Effect of Nanostructured Surface on Strength and Fracture Morphology in Dissimilar Bonding of Aluminum Alloy and Carbon Fiber Reinforced Thermoplastics Laminate

Integrating interfacial bonding and coordinated deformation in steel/Al bilayers via a pin-less friction stir-assisted synchronous joining-forming approach

Enhancing bonding synergy and mechanical response of metal/composite hybrid joints through physicochemical surface pretreatment

Feasibility study of friction stir joining of aluminium with carbon fibre reinforced thermoplastic composite

The Influence of Coating and Adhesive Layers on the Mechanical Performance of Additively Manufactured Aluminum–Polymer Hybrid Joints

Joining with Reactive Nano-Multilayers: Influence of Thermal Properties of Components on Joint Microstructure and Mechanical Performance

Achieving high strength friction lap spot joints of carbon fiber reinforced thermosetting composite to aluminum alloy with additional thermoplastic interlayer

On the strength of joints of metal-plastic composites of hot-formed steel with an AlSi coating and a thermosetting fiber reinforced compression material

Joining of Aluminum and CFRP via Laser Powder Bed Fusion: Influence of Experimental Set-Up and Laser Processing on Microstructure and Mechanical Properties

Soldering of steel sheets and zinc-coated aluminum by hybrid composite forging

Investigating the Effect of Applied Pressure on Reactive Multilayer Foil Joining

Microstructures and Mechanical Properties of Laser Penetration Welding Joint With/Without Ni-Foil in an Overlap Steel-on-Aluminum Configuration

Fracture Analysis of Competing Failure Modes of Aluminum-CFRP Joints Using Three-Layer Titanium Laminates as Transition

Optimization of Friction Lap Joining Parameters and Exploration Connection Mechanism of CFRPA6/6061-T6 Aluminum Alloy Hybrid Structures

Robust Heterojunctions of Metallic Alloy and Carbon Fiber-Reinforced Composite Induced by Laser Processing

Improving the interfacial bonding strength and suppressing shrinkage porosity of 6061Al/GFRTP hot-pressing joints via interfacial modification

Influence of a Ni-foil Interlayer on Fe/Al Dissimilar Joint by Laser Penetration Welding