Abstract:Journal of Composite Materials, Ahead of Print. During the last decades, environmental concerns and limited resources have set focus of research on lightweight, mechanically high-performing structures for the transportation industry, in order to reduce fuel consumptions and CO2 emissions. Friction Stir Joining (FSJ), as a variant of the Friction Stir Welding (FSW), is an innovative friction-based joining technique for metal-composite hybrid structures. Joining in the plasticized state below the melting temperature of the metal leads to a comparatively small heat-affected zone, so that only minor metallurgical changes occur. Additionally, only a short processing time and no additional weight in form of fasteners is needed. The main objective of this study is to evaluate the feasibility of metal-composite structures via FSJ, intending to enable a macro-mechanical interlocking bonding mechanism. Main focus was given to the integration of an aluminium nub inserted in a carbon fiber-reinforced polyphenylene sulfide (CF-PPS) sheet, to ensure sufficient plasticization of the aluminium part and no degradation in the polymer part. Residual stress arising from the friction stir joining process was also characterised using the Contour method. In this study, aluminium alloy 6082-T6 and CF-PPS composite sheets were used to produce long lap joints. Results have shown that the joints were created at almost constant peak temperature slightly above the melting temperature of the PPS but no physical-chemical changes were detected in the PPS. In addition, the influence of a PPS film as interlayer between the sheets was investigated in order to explore a method for preventing galvanic corrosion. Preliminary results indicate that it is not possible to integrate a metal nub to the CF-PPS without interrupting the PPS film. However, it is possible to create a nub within the PPS film.

Feasibility study of friction stir joining of aluminium with carbon fibre reinforced thermoplastic composite

Achieving high strength friction lap spot joints of carbon fiber reinforced thermosetting composite to aluminum alloy with additional thermoplastic interlayer

Evaluation of Joint Strength for CFRPs and Aluminum Alloys by Friction Stir Spot Welding Using Multi-Stage Heating

Flat Friction Spot Joining of Aluminum Alloy to Carbon Fiber Reinforced Polymer Sheets: Experiment and Simulation

Enhancing interfacial bonding in friction stir lap welding of light metal and carbon fiber reinforced polymer composite

New technique of friction-based filling stacking joining for metal and polymer

Influence of the interlayer film thickness on the mechanical performance of AA2024-T3/CF-PPS hybrid joints produced by friction spot joining

Joining of aluminium to polymer by friction stir welding: An overview

Research Progress in Joining of Carbon Fiber-Reinforced Polymer Composites and Aluminum/magnesium Alloys

Experimental and numerical investigation on failure behaviour of aluminum-polymer friction stir composite joints

Friction stir welding of lapped low-melt polyaryletherketone carbon fiber reinforced thermoplastic laminate

Optimization of Friction Lap Joining Parameters and Exploration Connection Mechanism of CFRPA6/6061-T6 Aluminum Alloy Hybrid Structures

Joining of Aluminum and CFRP via Laser Powder Bed Fusion: Influence of Experimental Set-Up and Laser Processing on Microstructure and Mechanical Properties

Friction stir lap welding for dissimilar materials of aluminum alloy and carbon-fiber-reinforced polyetherimide

A novel fed friction-stir (FFS) technology for nanocomposite joining

Effect of Carbon Fibre Reinforcement on an Aluminium Metal Matrix Composite Joint Through Upward Friction Stir Processing

Depriving friction stir weld defects in dissimilar aluminum lap joints

Study on the Microstructure and Mechanical Properties on Al/Carbon Fiber Reinforced Thermoplastic Dissimilar Friction Stir Lap Welding Joints

Friction stir spot welding of 5052 aluminum alloy to carbon fiber reinforced polyether ether ketone composites

Research on joint strength and energy absorption of CFRP and Al sheets bonded-FDS hybrid joining

Parameter optimization of friction stir spot welded Al 6061 and CFRTP PA6 with surface treatment and interfacial adhesion