Abstract:Laser metal deposition (LMD) additive manufacturing process was applied to produce ultrafine TiC particle reinforced Inconel 625 composite parts. The effects of laser energy input per unit length (LEIPUL) on microstructure development, densification response, and mechanical performance including wear performance and tensile properties were comprehensively studied. A relationship of processing conditions, microstructural characteristics, mechanical performance, and underlying strengthening mechanisms was proposed for a successful LMD of high-performance Inconel based composite parts. It revealed that using an insufficient LEIPUL of 33kJ/m lowered the densification behavior of LMD-processed parts, due to the appearance of residual large-sized pores in inter-layer areas of the parts. An increase in LEIPUL above 100kJ/m yielded the near fully dense composite parts after LMD. On increasing LEIPUL, the TiC reinforcing particles became significantly refined and smoothened via the elevated melting of particle surfaces and the dispersion state of ultra-fine reinforcing particles was homogenized due to the efficient action of Marangoni flow within the molten pool. The dendrites of Ni–Cr γ matrix underwent a successive change from an insufficiently developed, disordered microstructure to a refined, ordered microstructure with the increase of LEIPUL. However, the columnar dendrites of the matrix were coarsened apparently at an excessive LEIPUL of 160kJ/m because of the elevated thermalization of the input laser energy. The formation of the refined columnar dendrites of Ni–Cr γ matrix combined with the homogeneously distributed ultra-fine reinforcing particles contributed to the enhancement of wear performance of LMD-processed composites with a considerably low coefficient of friction (COF) of 0.30 and reduced wear rate of 1.3×10−4mm3/Nm. The optimally prepared TiC/Inconel 625 composite parts demonstrated a ductile fracture mode with a sufficiently high tensile strength of 1077.3MPa, yield strength of 659.3MPa, and elongation of 20.7%. The superior tensile properties of LMD-processed parts were attributed to the significant grain refinement effect of the matrix during laser processing and the efficient prohibition of ultrafine reinforcing particles on the mobility of dislocations.

Additive manufacturing and mechanical properties of TC4/Inconel 625 functionally graded materials by laser engineered net shaping

Influence of composition gradient variation on the microstructure and mechanical properties of 316 L/Inconel718 functionally graded material fabricated by laser additive manufacturing

Microstructure and Mechanical Properties of Ti60-Ti2alnb Functionally Graded Materials Fabricated by Laser Directed Energy Deposition

A functionally graded material design from stainless steel to Ni-based superalloy by laser metal deposition coupled with thermodynamic prediction

Fabrication and characterization of stainless steel 308 L / Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing

Microstructures and Mechanical Behaviors of Additive Manufactured Inconel 625 alloys via Selective Laser Melting and Laser Engineered Net Shaping

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

The effects and utility of homogenization and thermodynamic modeling on microstructure and mechanical properties of SS316/IN718 functionally graded materials fabricated by laser-based directed energy deposition

Dual-Wire Plasma Arc Additively Manufactured SS 316L-Inconel 625 Functionally Graded Material: Microstructure Evolution and Mechanical Properties

Functionally Graded Additive Manufacturing of Thin-Walled 316L Stainless Steel-Inconel 625 by Direct Laser Metal Deposition Process: Characterization and Evaluation

Research on the microstructure and mechanical properties of functional gradient materials of TC4/TC11 titanium alloys for wire arc additive manufacturing with different transitional forms

Study on Optimization Strategy for the Composition Transition Gradient in SS 316L/Inconel 625 Functionally Graded Materials

Grain morphology and mechanical properties tailoring of Inconel 625 alloy fabricated by laser powder bed fusion

Effect of synchronous electromagnetic stirring on Laves phase morphology and mechanical property of Inconel625-HSLA steel functionally graded material fabricated by wire arc additive manufacturing

Microstructural Features and Mechanical Integrity of Wire Arc Additive Manufactured SS321/Inconel 625 Functionally Gradient Material

Microstructure and Mechanical Properties of P21-STS316L Functionally Graded Material Manufactured by Direct Energy Deposition 3D Print

Functionally graded Inconel 718 processed by additive manufacturing: Crystallographic texture, anisotropy of microstructure and mechanical properties

Enhancing tensile properties of laser additive manufactured FeCoNiCrMn high entropy alloy via adding Fe-based metallic glass

Composition design and mechanical properties of B 4 C/Al-Zn-Mg-Cu functionally graded materials prepared by laser additive manufacturing

Additive manufacturing of a functionally graded material from Ti-6Al-4V to Invar: Experimental characterization and thermodynamic calculations

Laser Additive Manufacturing of Ultrafine Tic Particle Reinforced Inconel 625 Based Composite Parts: Tailored Microstructures and Enhanced Performance