The Common Faults and Solutions of TD75 Type Belt Conveyor

Chen Guang-min

Abstract:Belt conveyor as continuous conveying machinery was widely used in coal chemical industry production,but its use in the actual process had some trouble,and sometimes even affected the normal operation of production.The causes of belt conveyor's fault and its solutions were analyzed in detail.

Engineering,Materials Science

What problem does this paper attempt to address?

Fault Analysis of Belt Conveyor in Coal Mine

Zhag Xiao-qing

Abstract:Belt conveyor is a kind of critical equipment in coal mining production.The faults of belt conveyor were investigated in a coal mine in Shanxi province.It was concluded that belt offset,belt damage,electrical fault,starting problem,gear trouble and drum breakdown are common faults in coal mine,in which belt damage and electrical fault have higher percentages.According to the direct cause,the faults of belt conveyor can be classified into human initiated failure,equipment initiated failure and others.The percentage of human initiated failure can be more than 50%.In the five compositions of belt conveyor,i.e.driver parts,revolution parts,frame,electrical and auxiliary devices,the faults in driver parts and electrical devices are more than others.

Engineering,Environmental Science
Belt conveyer in the common faults and solutions

Yao Yong

Abstract:This paper analyzes the belt conveyor common fault causes,and aimed at these questions to propose solutions.

Engineering,Materials Science
Belt Conveyor Common Fault Analysis and Treatment Methods

Qin Lian-jun

Abstract:Belt Conveyor for transportation of goods as machinery,has been applied for many years in coal mine,coal mine is also an important one mining equipment by hanging-style development to the present use of seat belt-type transport aircraft,models,specifications vary,but installation,maintenance,maintenance and basically the same principle,is not much difference in the coal mine under the repair i used many years of practice,from the use of repair persons point of view,to talk about the common transport belt failure,the cause and maintenance of treatment ways.

Engineering,Environmental Science
Analysing of Common Breakdown of Mine Belt Conveyor and Treating Method

Wu Xian-hui

Abstract:Based on analyzing the common fault of mine belt conveyor system,the forms and the reasons of the faults are found out;therefore,we should take some measures to solve the troubles and instruct the production safety of the coal mine.

Engineering,Environmental Science
Application of fault diagnosis technologies in coal mine machinery

Yasong PU,Dewei GUO,Wenbin ZHANG

DOI: https://doi.org/10.13272/j.issn.1671-251x.2015.04.010

2015-01-01

Abstract:The paper introduced maintenance categories of coal mine machinery, pointed out predictability maintenance and initiative preventability maintenance based on fault diagnosis technology are development mainstreams of maintenance of coal mine machinery, expounded several popular fault diagnosis methods of coal mine machinery, and further summarized research hotspots and development trend of fault diagnosis technologies of coal mine machinery.
Analysis and Dispose of Deviation of Mine Belt Conveyor

Miao Zhang,Hong Liang Gao,Yang Zhang,Peng Zhan Wang

DOI: https://doi.org/10.4028/www.scientific.net/amm.608-609.685

2014-01-01

Applied Mechanics and Materials

Abstract:In order to improve the efficiency of coal production, the security and stability of the coal transportation plays a pivotal role. According to belt conveyor production operation of Huaibei mining area, this paper analyzes in detail the reasons of the deviation of belt and proposes some effective measures.
Big Declivitous DSJ100/90/2×250X Telescopic Belt Conveyor Application

Xu Hong-zhou

Abstract:This paper describes the DSJ100/90/2 ×250X telescopic belt conveyor in Xuehu coal mine 2102 fully mechanized coal mining face big declivitous machine roadway in the practical application,and to analyze the problems in the process of research,to improve its practicability,ensure mine high production efficient and safe production.

Environmental Science,Engineering
Design of Binary Telescopic Belt Conveyor

Shi Tong-ju

Abstract:The binary telescopic belt conveyor design to adapt to the rapid development of the mining face. It completed the integral design of the conveyor by analysis the main part,such as nose gear, roller groove, central groove, belt, braking device, storage device. From the right angle choose the spare parts in order to realize the machine running effect optimal, and conform to the requirements of the development of long distance, high power, high capacity of the belt conveyor.

Engineering
The Way of Full-Mechanized Coal Winning Face Conveyor Belt Vertical Join

Yan Ji

2002-01-01

Abstract:Based on require and need of coal mine in production.Analyzed the belt conveyor existing problem.working out optimum design of according to using characters.
Research and Analyze on Belt-conveyors of Purely Mechanical Belt-broken Seizing Machine

Jianzhong Luo,Guiyun Xu,Xudong Zhang,Yanfang Zhao

DOI: https://doi.org/10.1109/ICDMA.2011.222

2011-01-01

Abstract:Through the analysis of the status of belt-broken seizing machine and synthesizing the features of the common ones, designed a high reLiabiLity, minimal damage and purely mechanical belt-conveyors of belt-broken seizing machine according to the need of safe transport in the coal mine. The belt-broken seizing machine is made up of the agency of belt-broken signal capture and actuator that are purely mechanical. When occuring the belt-broken accident, broken belt drives the agency of belt-broken signal capture, which Links the actuator that connected to it to complete the action of seizing belt-broken. The agency of belt-broken also has a braking effect while Links the actuator, and achieve the dupLicate protection of the belt-broken with the actuator. Furthermore, the units has the advantages of that it is simple structure, easy to install, easy maintenance, sensitive and reLiable, avoid the second accident after the belt-conveyors broking, and ensure the safe transport of belt-conveyors in the coal mine.
Development and Application of Telescopic Belt Conveyor Transfer Drive End Unit

Wang Hai-chuan

Abstract:By Workface telescopic belt conveyor tail using the traditional method of shrinking the problems in analysis,research system,has done a hydraulic Moving Self-move the tail and face the three applications,with the production of simple,easy to operate,input cost less,the labor intensity of small,safe and practical advantages and popularization.

Engineering
On the design of telescopic system of belt conveyor

C. Lan,Baozhong Feng

DOI: https://doi.org/10.1117/12.2645476

2022-08-30

Abstract:Given that the disassembly speed of the body of the telescopic belt conveyor operated in an underground coal mine couldn’t keep consistent with the advancing speed of the working face, a telescopic system specially for the belt conveyor was designed. Then a detailed comparison of the merits and demerits and a force analysis of different telescopic systems were made in this paper. Lastly, a conveyor belt-oriented friction-type traction device was invented for specific working conditions. And the traction device is characterized by strong adaptability and high working efficiency and could retract and extend the telescopic part continuously and automatically, which provided an effective technical solution to facilitate the intelligent and efficient development of the modern mine.

Engineering
Dynamic characteristic analysis and startup optimization design of an intermediate drive belt conveyor with non-uniform load

Yu Feng,Miaotian Zhang,Guoping Li,Guoying Meng

DOI: https://doi.org/10.1177/0036850419881089

Abstract:As an important transportation equipment, belt conveyor plays an important role in underground coal mine production and is an indispensable component. In this article, taking the intermediate drive belt conveyor of Shanxi Tongmei Group Tongxin Mine as an example, the continuous dynamic method is adopted to comprehensively consider the non-uniform load distribution of the belt conveyor, and mathematical modeling of the intermediate drive belt conveyor is performed. The dynamic characteristics of the conveyor belt are analyzed. The MATLAB software is used to analyze the change of the conveyor belt tension under different starting accelerations. Based on the analysis results, the starting acceleration is optimized, and the new combined parabolic acceleration curve presented here is more suitable for the actual working condition of the belt conveyor. In this article, the startup timing of the head and middle motors of the belt conveyor is also discussed in depth. The start timing design of the belt conveyor is described, which provides a reference for the design of the belt conveyor with an intermediate drive.
Analysis on Mechanism and Characteristic of Vibration Fault on New Large Capacity Synchronous Condenser

Chenlong Li,Wen Gu,Chao Xia,Hewen Li,Fengjun He

DOI: https://doi.org/10.1088/1742-6596/2731/1/012002

2024-03-24

Journal of Physics Conference Series

Abstract:Vibration faults are the most common faults in large capacity synchronous condenser. The article proposes 11 common vibration faults of condenser, including imbalance, misalignment, looseness, resonance, oil film oscillation, steam flow excitation, dynamic static friction, rotational stall, gear fault, rolling bearing fault, and other vibration faults. The article also proposes the mechanism, characteristics and case analysis of each type of fault separately. The research results on the mechanisms and characteristics of these faults are the foundation of condenser fault diagnosis, and are crucial for the development of intelligent decision-making systems and platforms. Which can provide the strongest technical support for improving power transmission and safety and stability of the power grid.
Analysis and Discussion on Tension of Long Transport Belt

Haojie Mu

DOI: https://doi.org/10.1051/matecconf/202338001024

2023-01-01

MATEC Web of Conferences

Abstract:The technical field of belt tensioning force studied in this paper, in particular, relates to a hydraulic belt tensioning device, including a base, a hydraulic system and a rail fixed on the base, and a tail wheel trolley sliding on the rail; This device can provide a large tension to the tail wheel of the conveyor belt to meet the tension required by the long conveyor belt. At the same time, it can automatically adjust the tension to the tail wheel of the conveyor belt according to the tension of the conveyor belt to realize the dynamic tension control of the conveyor belt; The device prevents belt deviation and material leakage, reduces labor intensity of workers, avoids equipment accidents, and improves industrial production capacity.
Reliability Analysis of Belt Conveyor Based on Fault Data

Meiyan Li,SUN Yingqian,Chuan Luo

DOI: https://doi.org/10.1088/1757-899X/692/1/012009

2019-11-28

IOP Conference Series: Materials Science and Engineering

Abstract:In order to improve the accuracy of the reliable analysis of the belt conveyor, based on the belt conveyor fault data, firstly fit the probability density distribution function of the belt conveyor fault interval time. According to the characteristics of the fault data, it is inferred that it may obey the Weibull three-parameter distribution. The Weibull distribution model is obtained by combining the least squares method with the correlation coefficient method, and the accuracy of the model is verified by d test. Finally, the reliability of the belt conveyor is analysed, and the measures to improve the reliability of the belt conveyor are given, which provides a theoretical basis for the daily maintenance of the belt conveyor.
Reason analysis of common faults of frequency converter and handling

ZHANG Hao,HAO Pei-jun,CHANG Shu-jiang

DOI: https://doi.org/10.3969/j.issn.1674-1951.2009.02.012

2009-01-01

Abstract:The faults of frequency converters inslalled in subsidiary system of Shanxi Guohua Jinjie Energy Source Corporation Limited in 2007 were analyzed.The common faults of frequency converters and relevant handling measures were summarized and provided to relevant technican for reference.
Analysis of the Brake and the Contrary Stopping of Up Inclined Belt Conveyor

Yong Feng

2001-01-01

Abstract:This article analyses that the up inclined belt conveyer breaks and contrary stops,and that it analyses that relations and effect of starting and stopping in loaded process.
Fault Diagnosis of Double Pitch Time-Sharing Meshing Toothed Conveyor Chain Transmission System Based on Neural Network

Song Ding,Donglin Jiang,Hongyan Zhou

DOI: https://doi.org/10.1155/2022/8159609

IF: 1.43

2022-09-21

Mathematical Problems in Engineering

Abstract:With the rapid development of industry, the production and demand of automobiles have increased significantly. The generation of cars often requires tens of thousands of processes, consisting of hundreds of assembly lines to complete. Chain conveyors are widely used in the transportation of automobile assembly lines. The existing conveyor chains are roller chains. With the improvement of the requirements for conveyor reliability, synchronization, and environmental friendliness, the characteristics of roller conveyor chains restrict the further development of chain conveyors. It is urgent to study a new conveyor chain system to improve the synchronization, reliability, and environmental friendliness of chain conveyors on hundreds of assembly lines. In this paper, the mathematical modeling, meshing analysis, reliability, and environmental friendliness of the parameters of the components of the double pitch time-sharing meshing toothed conveyor chain system are studied. In addition, a novel fault diagnosis method of double pitch time-sharing meshing toothed conveyor chain transmission system based on neural network model is proposed in this paper.

engineering, multidisciplinary,mathematics, interdisciplinary applications
Hitachi Hydraulic Excavator Common Failure Analysis and Maintenance

Sheng Li,Zhu Shiwu

2011-01-01

Abstract:At present,widely used in the construction of the hydraulic excavator,in the course of the common faults are turning weakness;rotary motor loose;leakage due to bucket cylinder,the cylinder and control valve card,inability to work caused injury.Articles from the hydraulic excavator to analyze the cause of the fault structure,and proposed solution and recommendations.

The Common Faults and Solutions of TD75 Type Belt Conveyor

Fault Analysis of Belt Conveyor in Coal Mine

Belt conveyer in the common faults and solutions

Belt Conveyor Common Fault Analysis and Treatment Methods

Analysing of Common Breakdown of Mine Belt Conveyor and Treating Method

Application of fault diagnosis technologies in coal mine machinery

Analysis and Dispose of Deviation of Mine Belt Conveyor

Big Declivitous DSJ100/90/2×250X Telescopic Belt Conveyor Application

Design of Binary Telescopic Belt Conveyor

The Way of Full-Mechanized Coal Winning Face Conveyor Belt Vertical Join

Research and Analyze on Belt-conveyors of Purely Mechanical Belt-broken Seizing Machine

Development and Application of Telescopic Belt Conveyor Transfer Drive End Unit

On the design of telescopic system of belt conveyor

Dynamic characteristic analysis and startup optimization design of an intermediate drive belt conveyor with non-uniform load

Analysis on Mechanism and Characteristic of Vibration Fault on New Large Capacity Synchronous Condenser

Analysis and Discussion on Tension of Long Transport Belt

Reliability Analysis of Belt Conveyor Based on Fault Data

Reason analysis of common faults of frequency converter and handling

Analysis of the Brake and the Contrary Stopping of Up Inclined Belt Conveyor

Fault Diagnosis of Double Pitch Time-Sharing Meshing Toothed Conveyor Chain Transmission System Based on Neural Network

Hitachi Hydraulic Excavator Common Failure Analysis and Maintenance