Abstract:Highlights • A novel super wear-resistant coating for mg alloys was achieved via the new strategy of discontinuous deposition. • The wear resistance was exceptionally 5500 times superior to the base PEO coating. • The wear resistance was surprisingly 20 times superior to conventional continuous deposition. • The inducements of rolling friction, nano lubrication and the mixed wear of soft matrix and hard point result in the super wear resistance. Magnesium alloys are lightweight materials with great potential, and plasma electrolytic oxidation (PEO) is effective surface treatment for necessary improvement of corrosion resistance of magnesium alloys. However, the ∼14 μm thick and rough PEO protection layer has inferior wear resistance, which limits magnesium alloys as sliding or reciprocating parts, where magnesium alloys have special advantages by their inherent damping and denoising properties and attractive light-weighting. Here a novel super wear-resistant coating for magnesium alloys was achieved, via the discontinuous sealing (DCS) of a 1.3 μm thick polytetrafluoroethylene (PTFE) polymer layer with an initial area fraction (A f ) of 70% on the necessary PEO protection layer by selective spraying, and the wear resistance was exceptionally enhanced by ∼5500 times in comparison with the base PEO coating. The initial surface roughness (Sa) under PEO+DCS (1.54 μm) was imperfectly 59% higher than that under PEO and conventional continuous sealing (CS). Interestingly, DCS was surprisingly 20 times superior for enhancing wear resistance in contrast to CS. DCS induced nano-cracks that splitted DCS layer into multilayer nano-blocks, and DCS also provided extra space for the movement of nano-blocks, which resulted in rolling friction and nano lubrication. Further, DCS promoted mixed wear of the PTFE polymer layer and the PEO coating, and the PTFE layer (HV: 6 Kg/mm 2 , A f : 92.2%) and the PEO coating (HV: 310 Kg/mm 2 , A f : 7.8%) served as the soft matrix and the hard point, respectively. Moreover, the dynamic decrease of S a by 29% during wear also contributed to the super wear resistance. The strategy of depositing a low-frictional discontinuous layer on a rough and hard layer or matrix also opens a window for achieving super wear-resistant coatings in other materials.

Achieving the lightweight wear-resistant TiC reinforced AlFeCrCo medium-entropy alloy coating on Mg alloy via resistance seam processing

Optimized wear behaviors and related wear mechanisms of medium entropy alloy-based composite coatings

Preparation, mechanical properties and wear resistance of dual-sized TiC particles reinforced high-entropy alloy cermet coating

Ti3C2Tx-based composite coating on AZ31B Mg alloy surface for improved anti-corrosion/wear-reducing properties

Simultaneously Improved Corrosion/wear Resistances of Mg Alloy Through an Ultra-Thin Mg(OH)2/graphene-APTES Coating

Sequentially Bridged Biomimetic Graphene-Based Coating Via Covalent Bonding with an Effective Anti-Corrosion/wear Protection for Mg Alloy

Reinforcing Mechanism of WC Particles in Fe-Based Amorphous Matrix Coating on Magnesium Alloy Surface

Development of High Corrosion- and Wear-Resistant Al-Si Alloy Coating on AZ80 Mg Alloy by Hot Extrusion

A novel strategy for promoting corrosion and wear resistance of Mg-Li alloys: Gradient eutectic high-entropy alloy coating induced by in-situ bidirectional diffusion

Enhanced protective nanoparticle-modified MgAl-LDHs coatings on titanium alloy

Surface strengthening aluminum alloy by in-situ TiC-TiB2 composite coating

Tungsten carbide coating prepared by ultrasonic shot peening to improve the wear properties of magnesium alloys

A super wear-resistant coating for Mg alloys achieved by plasma electrolytic oxidation and discontinuous deposition

Microstructures, wear resistance and corrosion resistance of CoCrFeNi high entropy alloys coating on AZ91 Mg alloy prepared by cold spray

Significantly improved bonding strength of Al/Mg bimetallic interface by compound casting via FeCoNiCrCu high entropy alloy coating

Enhancing the wear resistance of titanium alloys through the synthesis of layered double hydroxides combined with titanium nitride coatings

Superior bonding of Al/Mg interface by introducing nanocrystals via high-entropy alloy coating and ultrasonic vibration

Preparation and properties of CrNiWMoCoTi gradient high entropy alloy layer by plasma surface metallurgy

Microstructure and Wear Resistance of FeCuNiTiAl High-Entropy Alloy Coating on Ti6Al4V Substrate Fabricated by Laser Metal Deposition

A Simple Surface Treatment for Mg to Gain Enhanced Resistance to Corrosion and Corrosive Wear by Hammering Al Powder‐Covered Mg Substrate

In-situ TiB2-TiC reinforced Fe-Al composite coating on 6061 aluminum alloy by laser surface modification