Abstract:With the rapid growth of shield-discharged soil (SDS), there is an increasing demand for effective recycling and transformation methods. This study aims to develop an alkali-activated controlled low-strength material (CLSM) by utilizing ground granulated blast furnace slag (GGBFS) and fly ash (FA) as precursors, SDS as fine aggregate, and sodium hydroxide (NaOH) solution as an activator. The Box-Behnken design (BBD) within the response surface methodology (RSM) framework was employed, considering liquid-to-solid ratio, alkali equivalent, aggregate-to-binder ratio, and foam agent content (FC) in SDS as key factors. Regression models were constructed to analyze the effects of these factors on flowability, bleeding rate, setting time, compressive strength, elastic modulus, and water absorption. The results confirmed the effectiveness of RSM in determining optimal conditions for material performance. In addition, microscopic analyses were conducted to explore hydration products, microstructural characteristics, and pore distribution. The findings revealed that the fresh density of the CLSM ranged from 1460 to 1740 kg/m3, classifying it as a low-density material. The 28-day compressive strength varied from 1.837 to 7.884 MPa, while the setting time ranged between 1.2 and 5.6 hours. These properties comply with the ACI 229 standard and are suitable for practical applications. Interestingly, when the aggregate-to-binder (A/B) ratio was between 0.2 and 0.4, increasing the ratio did not lead to a consistent reduction in mechanical properties. Instead, the properties initially decreased and then improved. Moreover, an increase in foam agent content (FC) extended the setting time and reduced mechanical strength. The correlation coefficients of all models exceeded 0.98, with a coefficient of variation below 10 % and a signal-to-noise ratio greater than 4, demonstrating strong reliability and accuracy of the models. Additionally, the average relative error between predicted and experimental values in six scenarios was under 6 %, validating the feasibility of optimizing the design of alkali-activated CLSM using RSM. The formation of Ca(OH)2 crystals facilitates early strength development, resulting in final cementitious materials reticular, fibrous C-S-H, C-A-H, and other gel-like hydration products. Calcium promotes the formation of gels such as C-S-H, shortening the setting time and enhancing microstructural density. This study provides valuable insights for optimizing the design of alkali-activated CLSM containing SDS, thereby expanding methods for utilizing construction and demolition waste.

Preparation of alkali-free liquid accelerator with fluorine-containing silicon residue and its accelerating mechanism

Properties and acceleration mechanism of cement mortar added with low alkaline liquid state setting accelerator

Exploration on the occurrence state of fluorine in cement hydration products mixed with high fluorine alkali free liquid accelerator

Accelerating strength development of cementitious mixtures using aluminum sulfate liquid accelerator with aluminium formate

Research on the Working Performance and the Corresponding Mechanical Strength of Polyaluminum Sulfate Early Strength Alkali-Free Liquid Accelerator Matrix Cement

Preparation and properties of hexafluorosilicic acid series accelerators

The Influence of Alkali-Free Shotcrete Accelerators on Early Age Hydration and Property Development within Cement Systems

Preparation and hydration mechanism of aluminum formate/aluminum sulfate based alkali-free composite accelerator for sprayed concrete

Formulation of an alkali-free accelerator and its effects on hydration and mechanical properties of Portland cement

Effects of Using Aluminum Sulfate as an Accelerator and Acrylic Acid, Aluminum Fluoride, or Alkanolamine as a Regulator in Early Cement Setting

Investigation of Low-Calcium Circulating Fluidized Bed Fly Ash on the Mechanical Strength and Microstructure of Cement-Based Material

Effect of Fluoride in Alkali-Free Liquid Accelerator on Corrosion of Reinforced Shotcrete by Chloride Ion

Influence of fly ash and granulated blast furnace slag on autogenous shrinkage and drying shrinkage of cement-based materials mixed with alkali accelerator and alkali-free accelerator

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Evaluation of setting and hardening properties of accelerator and slag-silica fume-cements

Optimization and characterization of GGBFS-FA based alkali-activated CLSM containing Shield-discharged soil using Box-Behnken response surface design method

Accelerators for Shotcrete – Chemical Composition and Their Effects on Hydration, Microstructure and Properties of Cement-Based Materials

Effect of Accelerators on the Workability, Strength, and Microstructure of Ultra-High-Performance Concrete

How Competitive Hydration between C 3 A and C 3 S in the Fast Dissolution Stage Affects the Hydration of Low-Heat Portland Cement Blended Pastes

Influence of Accelerators on Cement Mortars Using Fluid Catalytic Cracking Catalyst Residue (FCC): Enhanced Mechanical Properties at Early Curing Ages

Strength formation mechanism and curing system optimization of low-carbon cementitious materials prepared by synergistic activation of multiple alkaline solid wastes