Abstract:α-titanium alloys are extensively applied under cryogenic environment and thereby their cryogenic mechanical properties and service failures deserve to be deeply studied. Here, tensile behaviors and damage-fracture characteristics of Ti-2.5Cu α-titanium alloy were systematically investigated at liquid-nitrogen temperature (LT) plus room temperature (RT) for comparison. It is found that the LT samples possess superior strength and ductility concurrently. Both yield strength ( σ y ) and ultimate tensile strength ( σ b ) improve more than 70%, whilst total elongation at fracture ( A ) adds more than 33% in comparison with the RT counterparts. Meanwhile, the LT samples are stretched mainly by uniform strain without noticeable necking. Fracture analysis indicates that being different from typical cup-and-cone fracture surface in the RT samples, the 'radial' fracture surface appears in the LT samples. Such specific fracture surface is constructed by two characteristic morphologies of crack-initiation zone at sample surface and the ensuing crack-propagation zone. Furthermore, it is seen that a large number of micro-voids are dispersed underneath fracture surface in the RT samples, whereas the number of micro-voids is sharply reduced at LT. Nevertheless, Vickers hardness at the position is always much higher in the LT samples. These novel mechanical properties and damage-fracture characteristics in the LT samples are closely associated with the prevalent deformation twinning in microstructure. Deformation twinning itself and plentiful twins-induced dynamic Hall-Petch effect steadily accommodate plastic deformation , contributing to the simultaneous enhancement of strength and ductility. This process also results in high stress state in samples, increasing the sensitivity of surface cracking. Hence, the 'radial' fracture morphology is finally formed. These findings enrich our fundamental understanding on deformation-damage-fracture process of α-titanium alloys, and also provide implicit guidance for the design of titanium alloys with high performance.

Comparative study of room and cryogenic deformation behavior of additive manufactured Ti‐6Al‐4V alloy

Microstructural evolution and cryogenic-normal temperature deformation behavior of the near-α titanium alloy TA15 fabricated by laser powder bed fusion

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Simultaneous improvement in strength and ductility of CT20 titanium alloy at cryogenic temperature

Tailoring the Ductility of Ti-6Al-4V Titanium Alloy Fabricated by Laser Power Bed Fusion at Liquid Nitrogen Temperature

Effect of cryogenic temperature on the strengthening mechanisms of AZ61 Mg alloy extruded at different temperatures

Influence of pre-stretching at ambient and cryogenic temperatures on dislocation configuration, precipitation behaviour, and mechanical properties of 2195 Al-Cu-Li alloy

Mechanical properties and microscopic mechanisms of 2219-T6 aluminum alloy under dynamic tension with cryogenic temperatures

Superior tensile properties and unique damage-fracture characteristics of Ti-2.5Cu α -titanium alloy at liquid-nitrogen temperature

Effects of cryogenic pre-deformation on the microstructure and mechanical properties of Ti–Mo alloys

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

Investigation of enhanced strength anisotropy in an extruded Mg–Al–Ca–Mn alloy at cryogenic temperature

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

Cryogenic Deformation Behaviour of Aluminium Alloy 6061-T6

Effects of size, geometry, and testing temperature on additively manufactured Ti-6Al-4V titanium alloy

Mechanical Behavior Assessment of Ti-6Al-4V ELI Alloy Produced by Laser Powder Bed Fusion

Effects of temperature on tensile and fracture performance of Ti6Al4V alloy fabricated by laser powder bed fusion

The Effect of Annealing and Cryogenic Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy

Microstructure and Mechanical Properties of An Ultrahigh-strength Titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb Prepared Using Laser Directed Energy Deposition and Forging: A Comparative Study

Deep Cryogenic and Thermal Aging Treatments of Ti‐5Al‐5Mo‐5V‐3Cr Alloy Additively Manufactured by Powder Bed Fusion‐Laser Beam

Comparing the Cold, Warm, and Hot Deformation Flow Behavior of Selective Laser‐Melted and Electron‐Beam‐Melted Ti–6Al–2Sn–4Zr–2Mo Alloy