Abstract:Abstract Precise tooling is vital for defect-free production of micro injection moulded (μ-IM) or hot-embossed products. The demoulding stage of such moulding and forming processes poses a serious challenge to the integrity of thin miniature features because of friction, adhesion, and thermal stresses. Typically, micro moulds involve geometrically textured patterns or features such as linear ridges, pillars, channels, and holes, the characteristic dimensions of which range from 10 to 300 μm. Realistically complex mould designs, containing precision micro features (enhanced fillet radius and positive draft angle) and high surface quality, are presented in this work. Electropolishing based on forward pulse currents (PC) has been used to shape and polish Ni micro moulds that contain sets of micron-scaled linear ridges and star patterns in order to ease the separation of moulded polymeric parts from the metallic mould during ejection and demoulding. The use of forward pulsed currents improved the mould design by increasing the fillet radii and draft angle while keeping the surface roughness low and maintaining a good surface shine. An optimization study of forward PC using a green solution of nickel sulfamate varied EP times (0–70 min) and duty cycles (40, 50, 60, and 70%) at a process conditions of 2.8 V, 50 °C, and 250 rpm. The best topographical and morphological changes were observed for a typical microfluidic channel ( w × h , 100 × 110 μm) with an EP time of 70 min and 50% duty cycle: fillet radius increased by 3.8 μm, draft angle by 3.3°, and the channel width reduced by 11.4% while surface roughness changed by 8.6% and surface shine improved by 48.9%. Experimental validation was performed using hot embossing wherein the electropolished Ni mould replicated the micro channels and star patterns in PMMA chips with notably fewer burrs, material pile up, and no feature distortion. Moreover, there was a reduction in the side wall roughness of micro channels in PDMS casting with electropolished Ni mould by 16%. Hence, this work presents a significant scientific contribution to improving the efficiency of micro mould tools and reduces the defects caused by friction and adhesion in replicated polymeric parts.

Optimisation of a novel hot air contactless single incremental point forming of polymers

Development of Estimation Procedure of Contact Heat Transfer Coefficient at the Part–Tool Interface in Hot Stamping Process

Investigation of Advanced Robotized Polymer Sheet Incremental Forming Process

Mechanism Investigation for the Influence of Tool Rotation and Laser Surface Texturing (LST) on Formability in Single Point Incremental Forming

A New Tool Path with Point Contact and Its Effect on Incremental Sheet Forming Process

Parametric Optimization on Single Point Incremental Forming of Aluminum Alloy AA 2219-O using Response Surface Methodology

Optimization of Control Parameters in Micro Hot Embossing

Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

Heat-assisted friction stir incremental sheet forming of thermoplastics

Design of the Novel Hot Incremental Sheet Forming Experimental Setup, Characterization of Formability Behavior of Polyether-Ether-ketone (PEEK)

The High-Pressure Liquid Jet Incremental Forming for the Aluminum Sheet

Research on Sheet Metal Digital Incremental Forming Technology without Support

Optimization of forward pulsed currents for combining the precision shaping and polishing of nickel micro mould tools to reduce demoulding defects

Optimization of Forming Parameters in Incremental Sheet Forming of AA3003-H18 Sheets Using Taguchi Method

Experimental investigations of warm incremental sheet forming process on magnesium AZ31 and aluminium 6061 alloy

Relevant material characterization for load prediction in incremental forming

Thickness Control in A New Flexible Hybrid Incremental Sheet Forming Process

Enhanced forming height and accuracy of thin-walled aluminum alloy by impact pneumatic forming

Considerations on the Influence of the Tool/Sheet Contact Conditions for Incremental Forming of Niobium Sheets

Fabrication and control architecture of novel hybrid metal additive manufacturing incremental forming technology

Topology optimization of forming tools: pressure die in rotary draw bending process