Abstract:3D printing technology was introduced into the manufacturing of ceramic components. To obtain a new lightweight multifunctional structure with novel structure and excellent performance, and promote the deep combination of additive manufacturing and optimization design, ZrO2(3Y)/Al2O3 hollow lattice structure ceramics with two kinds of high precision and different porosity were prepared by vat photopolymerization in this paper, and the process optimization, microstructure evolution, and performance were studied. The hollow lattice structure with good molding accuracy and porosity of 35 %–55 % was prepared by component design, optimization of slurry, degreasing, and sintering process, which effectively avoided the ceramic cracking and collapse caused by resin volatilization. When the Al2O3 content was 6 wt%, dense ZrO2(3Y)/Al2O3 ceramics with grain refinement, excellent microhardness, and fracture toughness were obtained. The relationship between lattice structure and compressive strength was analyzed by simulation and compressive test. The results show that the compressive strength of the two hollow lattice structures decreases with the increase of porosity. The maximum compressive strength of 35 %-face-centered cubic (FCC) hollow lattice structure is 326 MPa, which is significantly higher than that of body-centered cubic (BCC) structure (240 MPa) with the same porosity. The hollow lattice ceramic structure with good comprehensive performance and lightweight will lay a foundation for the application of industrial heat insulation, high temperature catalysis, and purification carrier in the future.

A facile approach for preparing Al2O3 reticulated porous ceramics with optimized closed-cell struts and excellent mechanical properties

Preparation of Novel Reticulated Porous Ceramics with Textured Structures Enabled by in Situ Generated Interlocking Al2O3 Platelets

Preparation of Novel Reticulated Porous Ceramics with Textured Structures Enabled by in Situ Generated Interlocking Al2O3 2 O 3 Platelets

Preparation of Fly Ash-Based Porous Ceramic with Alumina as the Pore-Forming Agent

Factors affecting the microstructure of a fine ceramic foam

Preparation of Al 2 O 3 ceramics with long-range inter-locked platelet structures possessing high porosity and excellent mechanical strength

Preparation of Al2O3 Ceramics with Long-Range Inter-Locked Platelet Structures Possessing High Porosity and Excellent Mechanical Strength

Enhanced mechanical properties and decreased thermal conductivity of porous alumina ceramics by optimizing pore structure

High-strength and corrosion-resistant Al2O3 ceramics with excellent closed-cell structure

Influence of template strut morphology on the mechanical performance of SiC reticulated porous ceramics

Controlling the Structure and Mechanical Properties of Porous B4C Ceramics with Unidirectionally Aligned Channels Using Sintering Additives

Novel Method To Optimize the Structure of Reticulated Porous Ceramics

A Novel Approach to Fabricate Porous Alumina Ceramics with Excellent Properties Via Pore-Forming Agent Combined with Sol Impregnation Technique

Highly Porous and Hierarchical MgAl2O4 Ceramics with Improved Pore Connectivity Prepared from Gelled Particle-Stabilized Foams

Preparation of Large Effective Specific Surface Area Reticulate Porous Ceramics by Polymeric Foam Replication Process Using Recoating Technique

Novel design of elongated mullite reinforced highly porous alumina ceramics using carbonized rice husk as pore-forming agent

Lightweight porous Al2O3‐based ceramics with highly controllable performance via binder jetting

Preparation and Characterization of Mullite Foam Ceramics with Porous Struts from White Clay and Industrial Alumina

Fabrication of alumina ceramics with high flexural strength using stereolithography

Low sintering shrinkage and high strength of porous mullite–zirconia ceramics: Effect of AlF3 and ZrSi2 contents

3D printing of hollow lattice structures of ZrO2(3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties