Abstract:The stochastic morphology of ceramic foams and discrepancies between specimens of the same type complicate the creation of numerical models during the design and optimization of porous medium burners. A favourable solution, from the modelling point of view, is the application of an ordered diamond lattice with definite geometry produced by means of additive manufacturing, which potentially allows achieving higher efficiencies and lower pollutant emissions. This document, describes procedures in the selection of diamond lattices with proper parameters and the comparison of the porous medium burner performances with different materials and geometries. The first section explains our methodology for geometrical analysis of ceramic foams and further selection of equivalent diamond lattices. Three acquired types of ceramic SiSiC foams (10 PPI, 30 PPI, and 60 PPI) were evaluated from image cross-sections and digital replicas that were obtained by means of X-ray computed tomography. Upon investigating, we found that pore sizes provided by a manufacturer were underestimated and discrepancies between them reached up to 100% for 60 PPI specimens. Combination of adapted cell size analysis according to ASTM D3576-15 standard and a developed tetrakaidecahedron model was favoured among other methods of pore size determination. After analysis of ceramic foams, an approach of selecting equivalent diamond lattices in terms of porosity and absolute permeability was proposed. As a result, three specimens were printed from CoCr alloy: 10 PPI and 60 PPI foams, as well as an equivalent 10 PPI diamond lattice. A test bench of the two-section porous medium burner was designed and assembled, which allowed the temperature, pollutant emissions and pressure drop measurements. The second section describes the experimental procedures and results from six different setups that compared the foam and diamond lattice geometries, and compared ceramic and metal as materials. In all setups, pollutant emissions were low and at the detection limit of the equipment, which agrees with theory and previous research. The application of CoCr material was determined as advantageous in the upstream section, ensuring higher flame stability and structural strength. A diamond lattice was found to be a good candidate for replacement of the foam geometry by providing both the predictability and higher structural stiffness. We recommend that further research should be done on using diamond lattice geometries with CoCr alloy in the upstream section, and SiSiC ceramic foam in the downstream section for the broad range of lean combustion regimes.

The improvement of mechanical and combustion properties of SiC reticulated porous ceramics with multi-layer strut containing Ca/Cr co-doped LaAlO3 coating

The enhanced thermal shock resistance and combustion efficiency of SiC reticulated porous ceramics via the construction of multi-layer coating

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Combustion and thermal performance of a novel preheated miniature combustor with a flame holder and various porous medium materials

Corrosion behavior and failure mechanism of SiC whisker and c-AlPO4 particle-modified novel tri-layer Yb2Si2O7/mullite/SiC coating in burner rig tests

One zirconia-based ceramic coating strategy of combustion stabilization for fuel-rich flames in a small-scale burner

Direct Ink Writing of Hierarchical Porous SiC Ceramics As Catalyst Support for Hydrogen Production

Experiment on Lean Fuel Combustion in Porous Media Combustor with External Swiss-roll

Structural optimization of 3D printed SiC scaffold with gradient pore size distribution as catalyst support for methanol steam reforming

Effect of Activator on Properties of SiC Porous Ceramics

Methane/air Premixed Combustion in a Two-Layer Porous Burner with Different Foam Materials

A novel sintering additive system for porous mullite-bonded SiC ceramics: High mechanical performance with controllable pore structure

Effects of SDBS and ZrO2 additives on the microstructure and properties of silicon-bonded SiC porous ceramics

Experimental Study on Premixed Combustion in Two-Layer Porous Media with Embedded Heat Exchangers

Effect of the Cross-Section of a Porous Burner on the Combustion Stability Limit of Premixed Oxy-Methane Flames

Thermal cycling behavior of La2Zr2O7/Yb2Si2O7/SiC coated PIP Cf/SiC composites under burner rig tests

Thermal and structural performance of additively manufactured ceramic porous media burners

Design of porous medium burners by means of additive manufacturing

Effects of SiCnw/Al2O3 composite powders on properties of Al2O3–SiC refractory castables

Development and performace evaluation of a combustor with silicon carbide microchannel cooling

Premixed lean methane/air combustion in a catalytic porous foam burner supported with perovskite LaMn0.4Co0.6O3 catalyst with different support materials and pore densities