Abstract:In order to predict flow behavior and find the optimum hot working processing parameters for 5754 aluminum alloy, the experimental flow stress data obtained from the isothermal hot compression tests on a Gleeble-3500 thermo-simulation apparatus, with different strain rates (0.1⁻10 s⁻1) and temperatures (300⁻500 &deg;C), were used to construct the constitutive models of the strain-compensation Arrhenius (SA) and back propagation (BP) artificial neural network (ANN). In addition, an optimized BP⁻ANN model based on the genetic algorithm (GA) was established. Furthermore, the predictability of the three models was evaluated by the statistical indicators, including the correlation coefficient (R) and average absolute relative error (AARE). The results showed that the R of the SA model, BP⁻ANN model, and ANN⁻GA model were 0.9918, 0.9929, and 0.9999, respectively, while the AARE of these models was found to be 3.2499⁻5.6774%, 0.0567⁻5.4436% and 0.0232⁻1.0485%, respectively. The prediction error of the SA model was high at 400 &deg;C. It was more accurate to use the BP⁻ANN model to determine the flow behavior compared to the SA model. However, the BP⁻ANN model had more instability at 300 &deg;C and a true strain in the range of 0.4⁻0.6. When compared with the SA model and BP⁻ANN model, the ANN⁻GA model had a more efficient and more accurate prediction ability during the whole deformation process. Furthermore, the dynamic softening characteristic was analyzed by the flow curves. All curves showed that 5754 aluminum alloy showed the typical rheological characteristics. The flow stress rose rapidly with increasing strain until it reached a peak. After this, the flow stress remained constant, which demonstrates a steady flow softening phenomenon. Besides, the flow stress and the required variables to reach the steady state deformation increased with increasing strain rate and decreasing temperature.

Artificial neural network prediction to the hot compressive deformation behavior of Al–Cu–Mg–Ag heat-resistant aluminum alloy

Dynamic Behavior and Modified Artificial Neural Network Model for Predicting Flow Stress During Hot Deformation of Alloy 925

Prediction of Flow Stress of Annealed 7075 Al Alloy in Hot Deformation Using Strain-Compensated Arrhenius and Neural Network Models

Hot Deformation Flow Behaviour Modelling of Cast-Extruded Al 7075 Alloy Using Arrhenius Equations and Artificial Neural Network

Modeling of Flow Stress of As-Rolled 7075 Aluminum Alloy during Hot Deformation by Artificial Neural Network and Application

Modeling the Hot Deformation Behaviors of As-Extruded 7075 Aluminum Alloy by an Artificial Neural Network with Back-Propagation Algorithm

The Use of ANN to Predict the Hot Deformation Behavior of AA7075 at Low Strain Rates

Modeling of hot deformation behavior and prediction of flow stress in a magnesium alloy using constitutive equation and artificial neural network (ANN) model

A Modified Back Propagation Artificial Neural Network Model Based on Genetic Algorithm to Predict the Flow Behavior of 5754 Aluminum Alloy

The Prediction of Flow Stress in the Hot Compression of a Ni-Cr-Mo Steel Using Machine Learning Algorithms

Research on constitutive model of aluminum alloy 7075 thermal deformation based on deep neural network

Prediction of the Hot Compressive Deformation Behavior for Superalloy Nimonic 80A by BP-ANN Model

[Are tick medications pesticides? Implications for health and risk perception for workers in the dairy cattle sector].

Application of Constitutive Models and Machine Learning Models to Predict the Elevated Temperature Flow Behavior of TiAl Alloy

Microstructural evolution and constitutive analysis of Al-Mg-Zn-Er-Zr based on arrhenius-type and machine-learning algorithm

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Hot Compression Behavior and Processing Map of Homogenized Al-Mg-Si Alloy

Thermal Deformation Behavior of Mg–3sn–1mn Mg Alloy Based on Constitutive Relation Model and Artificial Neural Network

Thermal deformation behavior of Mg–3Sn–1Mn alloy based on constitutive relation model and artificial neural network

On the Prediction of Flow Stress Behavior of Additively Manufactured AlSi10Mg for High Temperature Applications

Predicting High Temperature Flow Stress of Nickel Alloy A230 Based on an Artificial Neural Network