Abstract:Additive manufacturing (AM) of metal usually forms columnar grains along the building direction due to the focused thermal energy directly heating the deposition layer to easily obtain an obvious temperature gradient. The columnar grains are not conducive to AM-sample application, which results in the property anisotropy of the AM-sample. In this work, a novel directed energy deposition-arc (DED-Arc) method for depositing layers without direct heating by focused thermal energy is proposed. The arc burns between the tungsten electrode and a water-cooled electrode, were only used to melt the wire during DED-Arc process. Using stainless steel wire as a model alloy, by studying droplet transfer, morphology of the deposition layer and microstructure evolution, the feasibility of the method was fully verified. Two kinds of droplet transfer modes were observed, and the difference between them was whether the droplet contacted the molten pool before falling off. The focused thermal energy is only used to melt the wire, and the droplet transfer cycle is mainly affected by gravity, greatly decreasing the heat accumulation compared with existing methods. The heat-affected zone (HAZ) was obviously inhibited. The grain morphology of the deposition layer mainly consists of equiaxed crystals (∼300μm) without an obvious preferred orientation. The deposition layer without direct heating by focused thermal energy could reduce the heat accumulation, resulting in a decrease in the temperature gradient and the morphology of equiaxed grains. The microstructure of a cylindrical sample was produced and has the same characteristics as with the deposition layer. The average microhardness of 172.63 HV, 167.95 HV and 169.26 HV are obtained in the top, middle and bottom regions, respectively. In addition, the tensile strengths are 500MPa and 490MPa, respectively.

The effect of direct energy deposition Arc mode on the porosity of AA5087 aluminium alloy

Correlations between Microstructure Characteristics and Mechanical Properties in 5183 Aluminium Alloy Fabricated by Wire-Arc Additive Manufacturing with Different Arc Modes

Effect of Travel Speed on the Properties of 5087 Aluminum Alloy Walls Produced by Wire and Arc Additive Manufacturing

Basic Research of Directed Energy Deposition for Aluminum 4043 Alloys Using Pulsed Variable Polarity Gas Metal Arc Welding

Porosity in wire-arc directed energy deposition of aluminum alloys: Formation mechanisms, influencing factors and inhibition strategies

Investigate the effect of arc characteristic on the mechanical properties of 5A56 Al alloy in CMT arc additive manufacturing

Effect of pulsed metal inert gas (pulsed-MIG) and cold metal transfer (CMT) techniques on hydrogen dissolution in wire arc additive manufacturing (WAAM) of aluminium

Processing of Haynes® 282® Alloy by Direct Energy Deposition with Arc and Wire

A comparative study on microstructure and mechanical properties of wire-arc directed energy deposited Al–Zn–Mg–Cu alloy based on the cold metal transfer technology

Influence of Metal Transfer Modes on Pore Formation during the Welding Process of AA6082/A360 Dissimilar Aluminum Alloys

Influence of Arc Mode on the Microstructure and Mechanical Properties of 5356 Aluminum Alloy Fabricated by Wire Arc Additive Manufacturing

Development of a New Cold Metal Transfer Arc Additive Die Manufacturing Process

The effect of heat input on the microstructure and mechanical properties of 18Ni 300 maraging steel fabricated by arc directed energy deposition

A novel directed energy deposition-arc method of deposition layer without focused thermal energy heating: droplet transfer, morphology and microstructure

Investigation of Mechanical Properties and Microstructure Analysis of 5356 Al Alloy Thin Plate and Block Fabricated by Directed Energy Deposition-Arc

Microstructure Evolution and Mechanical Behavior of 2219 Aluminum Alloys Additively Fabricated by the Cold Metal Transfer Process

Effects of different WAAM current deposition modes on the mechanical properties of AISI H13 tool steel

Influence of Arc Length Correction on Microstructure, Mechanical Properties, and Defect Formation of Wire-Arc Additive Manufactured 5356 Alloy

Quantitative characterization of porosity in Fe–Al dissimilar materials lap joint made by gas metal arc welding with different current modes

Characterization of 5356 Aluminum Walls Produced by Wire Arc Additive Manufacturing (WAAM)

Effect of Interlayer Temperature on the Formation Characteristics and Microstructure Evolution of the 304 Stainless Steel Fabricated by-CMT Directed Energy Deposition-Arc Manufacturing