Abstract:Wire + arc additive manufacturing (WAAM) is a state-of-the-art and highly efficient technique utilized to produce near net-shaped products on a large scale, employing a layer-by-layer approach. This research used pulsed current mode welding for single-layer bead-on-plate experiments to optimise the process parameters for WAAM of Hastelloy C-276. The effect of process parameters including pulsed current, pulsed frequency, and pulse duty cycle was systematically investigated on the weld appearance, depth of penetration, layer width, and layer height. The optimisation of single layer experimental runs was conducted using Box-Behnken designs (BBD) and the response surface method to construct several regression models. An analysis of variance was employed to validate the accuracy of both the measured and generated models. The BBD results indicate that interactions have a more significant impact on the peak current parameter than the resulting impact of pulse duty cycle and frequency. Validation tests were performed on the model with the optimal process variables that were identified, and its mechanical and metallurgical properties were analysed. Macrostructure and microstructural analysis of the single layer showed that the specified process parameters led to acceptable base metal fusion and bead is free from cracking. There was a considerable decrease in elemental segregation while using the pulse mode technique. Finer grain structure and reduced microsegregation enhance the hardness. Further residual stress (RS) at weld bead and base plate was 213 MPa and −240 MPa. Nonhomogeneous heat transfer during welding affects RS compressive and tensile characteristics. WAAM printing quality requires precise control of LH, LW, and DOP. This research aimed to propose suitable parameter values for manufacturing WAAM component for usage in chemical processing, nuclear, marine, and industrial settings by using unique pulsing features.

Effect of pulsed metal inert gas (pulsed-MIG) and cold metal transfer (CMT) techniques on hydrogen dissolution in wire arc additive manufacturing (WAAM) of aluminium

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

Porosity control and properties improvement of Al-Cu alloys via solidification condition optimisation in wire and arc additive manufacturing

Microstructures and Mechanical Properties of Al–Zn–Mg Aluminium Alloy Samples Produced by Wire + Arc Additive Manufacturing

Development of a New Cold Metal Transfer Arc Additive Die Manufacturing Process

Characterization of 5356 Aluminum Walls Produced by Wire Arc Additive Manufacturing (WAAM)

Effect of solution treatment on porosity, tensile properties and fatigue resistance of Al–Cu alloy fabricated by wire arc additive manufacturing

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

Influence of pulsed current GTAW-WAAM process parameters on the single layer bead geometry and multi bead multi-layer deposition of a nickel-based superalloy

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Preparation and characterization of CMT wire arc additive manufacturing Al-5%Mg alloy depositions through assisted longitudinal magnetic field

Manipulating nanostructure during wire arc additive manufacturing defeats hydrogen embrittlement

Hot-wire Arc Additive Manufacturing of Aluminum Alloy with Reduced Porosity and High Deposition Rate

Investigations and Multi-response Optimization of Wire Arc Additive Manufacturing Cold Metal Transfer Process Parameters for Fabrication of SS308L Samples

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Influence of Heat Treatment and Inter-Layer Rolling on the Evolution of Micropores in the Additively Manufactured Aluminum Alloys

The effects of ultrasonic frequency pulsed arc on wire + arc additively manufactured high strength aluminum alloys

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys

Influence of oxygen content in the shielding gas chamber on mechanical properties and macroscopic structure of Ti-6Al-4V during wire arc additive manufacturing

Metal Transfer Behavior and Molten Pool Dynamics in Cold Metal Transfer Pulse Advanced Additive Manufacturing of 7075 Aluminum Alloy