Abstract:Abstract Studies have shown the influence of WAAM process parameters on mechanical properties, bead formation, dimensional accuracy, and microstructure. However, metal transfer modes and their interactions with input variables have not been investigated thoroughly. Therefore, short/spray, pulse and double pulse modes were investigated in this study at different current levels. Bead-on-plate trials were conducted by depositing ER70S-6 wire to investigate bead morphology, dilution, microstructure, and hardness. The study was supported by a detailed statistical approach, including analysis of variance (ANOVA) and regression analysis. Similarly, the combined effects of hatch distance and current were studied on bead formation in multi-layer deposits. Moreover, a thin wall and a cubic structure were deposited to realize the WAAM capability for larger depositions. The microstructures of thin wall and cubic structure were analyzed using optical microscopy (OM) and scanning electron microscopy (SEM). The study concludes that metal transfer modes at various currents significantly influence bead geometry, microstructure and hardness. The microstructure of bead-on-plate trials show fine lamellar structure at low current in all modes. Higher current results in coarse grains with a polygonal and columnar morphology. The hardness shows a decreasing trend as the current increases. The combined effects of current and hatch distance alter bead morphology; however, an optimized combination yields smoother surfaces. The microstructure of thin wall showed a slight anisotropy along the building direction. The presence of small pores was witnessed from OM and SEM images. Similarly, the cubic structure showed a more homogeneous microstructure with much lower porosity. The hardness profile of the thin wall exhibited small fluctuations along the building direction, while that of the cubic structure was more uniform.

Manipulating nanostructure during wire arc additive manufacturing defeats hydrogen embrittlement

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Hydrogen Embrittlement of Ni-Based Superalloy Inconel 625 Fabricated by Wire Arc Additive Manufacturing: The Role of Laves Phase

Effect of pulsed metal inert gas (pulsed-MIG) and cold metal transfer (CMT) techniques on hydrogen dissolution in wire arc additive manufacturing (WAAM) of aluminium

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Periodic Microstructure of Al–Mg Alloy Fabricated by Inter-Layer Hammering Hybrid Wire Arc Additive Manufacturing: Formation Mechanism, Microstructural and Mechanical Characterization

Effect of Induction Heat Treatment on Residual Stress Distribution of Components Fabricated by Wire Arc Additive Manufacturing

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Wire arc additive manufacturing using high-strength steel tubular and solid wires

Effect of additional side shielding on the wire arc additive manufacturing of AZ31 magnesium alloy

Influence of metal transfer behavior under Ar and CO2 shielding gases on geometry and surface roughness of single and multilayer structures in GMAW-based wire arc additive manufacturing of mild steel

Microstructural development during wire arc additive manufacturing of copper-based components

Elucidating the effects of metal transfer modes and investigating the material properties in wire-arc additive manufacturing (WAAM)

Multiscale analysis of mechanical behavior of multilayer steel structures fabricated by wire and arc additive manufacturing

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

On the fabrication of finer grain structure through using finer wire diameter for wire arc additive manufacturing of AZ31B magnesium alloy

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Effects of annealing on periodic microstructure and mechanical properties of inter-layer hammering hybrid wire arc additively manufactured aluminum alloy

Hydrogen Embrittlement in Metallic Nanowires.