Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Interfacial Engineering by In Situ Building of a 3D/2D Heterojunction for Inverted CsPbI 2 Br Solar Cells: Beyond Moisture Proof

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

In Situ Formation of a 2D/3D Heterostructure for Efficient and Stable CsPbI2Br Solar Cells

Architecturing 1D‐2D‐3D Multidimensional Coupled CsPbI 2 Br Perovskites toward Highly Effective and Stable Solar Cells

π-π conjugate structure enabling the channel construction of carrier-facilitated transport in 1D–3D multidimensional CsPbI2Br solar cells with high stability

Constructing an Interfacial Gradient Heterostructure Enables Efficient CsPbI3 Perovskite Solar Cells and Printed Minimodules

In Situ Forming of a 2D Inorganic Perovskite Capping Layer by Surface Reconstruction for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Stiffening the Pb-X Framework through a π-Conjugated Small-Molecule Cross-Linker for High-Performance Inorganic CsPbI 2 Br Perovskite Solar Cells

2D/3D heterojunction engineering at the buried interface towards high-performance inverted methylammonium-free perovskite solar cells

In‐Situ Self‐Assembly Dipole Shielding Layer Toward Efficient and Stable Inorganic Perovskite Solar Cells

Passivating Dipole Layer Bridged 3D/2D Perovskite Heterojunction for Highly Efficient and Stable p‐i‐n Solar Cells

Stable High‐Efficiency CsPbI2Br Solar Cells by Designed Passivation Using Multifunctional 2D Perovskite

Bulk passivation and suppressing non-radiative recombination loss in a 3D all-inorganic CsPbIBr2 perovskite solar cell via a 2D layered perovskite framework

In Situ-Grown 2D Perovskite Based on π-Conjugated Aggregation-Induced Emission Organic Spacer Boosting the Efficiency and Stability of 2D-3D Heterostructured Perovskite Solar Cells

Two birds with one stone: Simultaneous realization of constructed 3D/2D heterojunction and p-doping of hole transport layer for highly efficient and stable perovskite solar cells

Dimensional Regulation from 1D/3D to 2D/3D of Perovskite Interfaces for Stable Inverted Perovskite Solar Cells

Modifying Surface Termination of CsPbI 3 Grain Boundaries by 2D Perovskite Layer for Efficient and Stable Photovoltaics

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

2D/3D heterostructured CsPbI2Br solar cells: a choice for a monolithic all-perovskite tandem device

Inorganic‐Derived 0D Perovskite Induced Surface Lattice Arrangement for Efficient and Stable All‐Inorganic Perovskite Solar Cells

High‐Performance CsPbIxBr3‐x All‐Inorganic Perovskite Solar Cells with Efficiency over 18% Via Spontaneous Interfacial Manipulation