Abstract:Carbon fiber reinforced plastics (CFRP), which are widely used in the aerospace and some other new-tech industries, are considered very difficult to machine due to the material anisotropic and inhomogeneous features. Chemical vapor deposition (CVD) diamond films are suitable as protective coatings on cutting tools for machining advanced composite materials, owing to their extremely high hardness, favorable wear resistance, low friction coefficient and high thermal conductivity. Among different types of diamond films, the fine grained diamond (FGD) film can provide much more favorable environment for machining CFRP due to the small grain size, low surface roughness and the retentivity for the sharpness of the cutting edge. In the present study, aiming at drilling CFRP, FGD films of different thicknesses are deposited on Φ3 mm drills by controlling the growth time, adopting the common-used hot filament CVD (HFCVD) technology. It can be directly proved by deposition experiments that overlong growth time can induce spontaneous film delamination and removal before the cooling stage, probably as a result of the excessive residual stress concentrated on the complicated surfaces. As demonstrated by the cutting tests, with increasing the growth time, the main failure mode of the FGD coated drill changes from film delamination to flank wear/tipping to film delamination, and the maximum tool life exists when the growth time is moderate, because the flimsy film cannot provide sufficient protective effects on the film-substrate interface and even hasn’t totally cover the substrate, while there’s relatively higher residual stress in the film that is too thick, and such the residual stress can significantly deteriorate the film-substrate adhesion. Moreover, during the life cycle of each FGD film, relatively shorter growth time often means the slightly better hole quality, attributed to the retentivity of the initial shape of the uncoated drill that is optimal designed for machining CFRP, especially the weaker passivation of the cutting edge.

Fabrication of copper/diamond functionally graded materials for grinding wheels by centrifugal sintered-casting

Drilling CFRP Laminates by Dual-Axis Grinding Wheel System With Copper/Diamond Functionally Graded Grinding Wheel

Fabrication of Diamond/w–cu Functionally Graded Material by Microwave Sintering

Fabrication and use of Cu-Cr-diamond composites for the application in deep feed grinding of tungsten carbide

Fabrication of W–Cu Functionally Graded Material with Improved Mechanical Strength

Functionally Graded Material Production and Characterization using the Vertical Separator Molding Technique and the Powder Metallurgy Method

A review on fabrication and characteristics of functionally graded aluminum matrix composites fabricated by centrifugal casting method

Effect of Main Parameters on the Mechanical and Wear Behaviour of Functionally Graded Materials by Centrifugal Casting: A Review

Fabrication Of Sic/Cu Functionally Gradient Material By Graded Sintering

Fabrication of Al2O3/TiC/Ni Functionally Graded Materials by Pulsed-Electric Current Sintering and Their Mechanical Properties.

Development and Characterization of 316l/inconel625 Functionally Graded Material Fabricated by Laser Direct Metal Deposition

Preparation of Cu/SiC FGM by Coating Method and SPS Sintering

Fabrication and microstructure of W/Cu functionally graded material

Study on Fabrication and Cutting Performance of CVD Diamond Coated Drills in Machining the Carbon Fiber Reinforced Plastics

Fabrication and Grinding Performance of CVD Diamond Abrasive Tool

Fabrication of ZrO2–NiCr Functionally Graded Material by Powder Metallurgy

Fabrication process of smooth functionally graded materials through a real-time inline control of the component ratio

Fabrication and characterization of machinable Si3N4/h-BN functionally graded materials

Growth Time Optimization of Fine Grained Diamond Coated Drills for Machining CFRP

Fabrication and Application of W/Cu Functionally Graded Material

Novel design and composition optimization of self-lubricating functionally graded cemented tungsten carbide cutting tool material for dry machining