Abstract:Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Structure and Morphology of Biaxially Oriented Films of Polyethylenes

The Microstructure-Tensile Property Relationship of Polyethylene Resin for Biaxially Stretched Film

Structure Evolution and Properties Enhancement of Polyamide‐6/polyamide‐1010 Films under Uniaxial and Biaxial Stretching

Chain Structure and Mechanical Properties of Ethylene Copolymers in Two Operating Modes of Fluidized Bed Polymerization Reactor

Segmental Orientations and Deformation Mechanism of Poly(Ether-Block-Amide) Films

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Deformation and Molecular Orientation in Films of Metallocene Polypropylene, Ethylene-Butylene Rubber, and Their 80/20 (W/W) Blend Revealed by the Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism, Macroscopic Stress, and Mesoscale Strain

Inhomogeneous Deformation of Microcrystalline Region in Isotactic Polypropylene Film Revealed by A Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. 2. Molecular Orientation During Necking Process of Isotactic Polypropylene

Morphological Study of Oriented Films Obtained from Side-Chain Liquid Crystalline Polymers

Structural characters of biaxially stretched polypropylene films and the relevant electrical insulating properties

The Effect of Architecture on the Morphology and Crystallization of Oxyethylene/oxybutylene Block Copolymers from Micelles in N-Hexane

Kinematics, Structure, And Properties Relationship Of Polyethylene Blown Films

Structure and Morphology Development in Films of mLLDPE/LDPE Blends During Blowing

Nanostructure and Mechanical Measurement of Highly Oriented Lamellae of Melt-Drawn HDPE by Scanning Probe Microscopy

Elucidation of the relationships of structure-process-property for different ethylene/α-olefin copolymers during film blowing: An in-situ synchrotron radiation X-ray scattering study

Morphology Control of Perpendicularly Oriented Lamellar Films from Azobenzene-Containing Block Copolymers with Different Spacer Lengths

Morphological-Studies Of Oriented Films Obtained From Aromatic Polyester Fractions

The Chain Microstructure And Condensed Structure Of Polyethylene Resin Used For Biaxially Stretched Film

Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film

Optimization of the cellular morphology of biaxially stretched thin polyethylene foams produced by extrusion film blowing