Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Suppressing Excess Lead Iodide Aggregation and Reducing N‐Type Doping at Perovskite/HTL Interface for Efficient Perovskite Solar Cells

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Suppressing the crystallographic disorders induced by excess PbI 2 to achieve trade-off between efficiency and stability for PbI 2 -rich perovskite solar cells

Enhancing the Efficiency and Stability of Triple-Cation Perovskite Solar Cells by Eliminating Excess PbI2 from the Perovskite/Hole Transport Layer Interface

Regulation of Lead Iodide Crystallization and Distribution for Efficient Perovskite Solar Cells

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Regulation of the Buried Interface to Achieve Efficient HTL-Free All-Inorganic CsPbI2Br-Based Perovskite Solar Cells

Ligand‐Induced In Situ Epitaxial Growth of PbI2 Nanosheets/MAPbI3 Heterojunction Realizes High‐Performance HTM‐Free Carbon‐Based MAPbI3 Solar Cells

Synergetic Excess PbI2 and Reduced Pb Leakage Management Strategy for 24.28% Efficient, Stable and Eco‐Friendly Perovskite Solar Cells

High-Light-Tolerance PbI 2 Boosting the Stability and Efficiency of Perovskite Solar Cells

Increasing the wettability and reducing excess PbI2 using diamine hydrobromides with different lengths at the buried interface of the 3D perovskite film

Surface Regulation via Carboxylate Polymer for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Enhancing perovskite solar cells efficiency through cesium fluoride mediated surface lead iodide modulation

Excess PbI2 Management via Multimode Supramolecular Complex Engineering Enables High‐Performance Perovskite Solar Cells

Preferentially Coordinating Tin Ions to Suppress Composition Segregation for High-performance Tin-lead Mixed Perovskite Solar Cells

Surface charge-transfer doping for highly efficient perovskite solar cells

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Passivating Defects via Retarding the Reaction Rate of FAI and PbI2 Enables Stable Perovskite Solar Cells

Ligand‐Modulated Excess PbI2 Nanosheets for Highly Efficient and Stable Perovskite Solar Cells

Suppressing halide phase segregation in wide-bandgap perovskite film by co-doping strategy for high-performance and stable perovskite solar cells