Abstract:Orbit (04/11/2019) Laser Induced Selective Activation For Subsequent Autocatalytic Electroless Plating The subject of this PhD thesis is “Laser induced selective activation for subsequent autocatalytic electroless plating.” The objective of the project is to investigate the process chains for micro structuring of polymer surfaces for selective micro metallization. Laser induced selective activation (LISA) is introduced and studied as a new technique for producing 3D moulded interconnect devices (3D-MIDs). This technique enables the metallization of polymer surface modified by laser and subsequently activated by a PdCl2/SnCl2 system. Various technologies exist on an industrial level for manufacturing MIDS, e.g. LDS®, 2-shot injection moulding, etc. Compared with them, LISA shows economic and environmental advantages. First, the range of available polymers is wide, and no pretreatment such as filler premix is need. Commercial polymer such as polyethylene and polystyrene, polycarbonate, ABS, etc. can be directly used in the LISA process. Second, in the wet steps, no chromic acid or other similar toxic compounds are used. The principle of the PdCl2/SnCl2 activation system is explained based on previous researchers’ studies. Investigations were conducted as to how the laser tracks keep the activation colloids based on three hypotheses. The first hypothesis is that laser machining leads to chemical changes of the polymer, which results in chemical bonding with the activation colloids. Chemical changes on the laser track were investigated by XPS or FTIR spectroscopy, but no evidence shows that chemical bonds exist. However, it is still not excluded that chemical bonding is part of the mechanism. The second hypothesis is that the laser track has a stronger attraction work to the activation solution. This is proved by a calculation using van Oss et al., theory based on contact angle measurement. The third hypothesis is that the activation and rinsing process can be described by diffusion. This hypothesis is proved using Fick’s diffusion laws combined with the short-time-plating experiment. The influence of laser parameters on the surface structure is investigated for Nd:YAG, UV, and fiber lasers. The mechanism of the surface structure formation reason is discussed and the Nd:YAG laser parameters’ effect on the structure of the laser track is investigated. There is a trend showing that the height of the laser track increases with the laser energy output. A characterization method for the porous surface based on the bearing area curve and its parameters is propsed. Comparison of two activation methods based on plating velocity was performed. It was found that the plating velocity is independent of the height of the laser track, as long as the structure is sponge-like and continuous. The adhesive strength of the copper coating is related to the laser structure. High laser energy input will lead to high laser track, on which the copper coating has a stronger adhesion than on the track made by lower energy, even though the coatings have similar thickness. The LISA method was tested in the case of an antenna. Two simple antenna shapes, planar dipole, and planar loop were studied, as well as a co-planar stripline. The antennas made by LISA exhibited impedance characteristics expected from the respective antenna shapes and comparable to antennas made by PCB technology.

A new laser assisted palladium-free activation technology for ABS plastic surface electroless copper plating

A New Palladium-Free Surface Activation Process for Cu Electroless Plating on ABS Plastic

Electroless Copper Plating on PC Engineering Plastic with a Novel Palladium-Free Surface Activation Process

Technology of Electroless Copper Plating on ABS Plastics

Preparation of Electroless Copper Circuit on Polycarbonate/ Acrylonitrile Butadiene Styrene (PC/ABS) Using a Laser curing of Pd complex

Process of Direct Copper Plating on ABS Plastics

Electroless nickel plating on the surface of ABS plastic without palladium activation

Photoselective Deposition of Copper Lines on ABS Substrates by Electroless Plating

Electroless Plating of Copper via a Sn-Free Process on Dielectric SiLK Surface Modified by UV-Induced Graft Copolymerization with 4-Vinylpyridine and 1-Vinylimidazole

Colloidal Silver Activation for Electroless Copper Deposition

Study on a New Activation Method for Initiating Electroless Plating on Alumina Powders Based on SAMs Bonded Palladium

Electroless Deposition of Confined Copper Layers Based on Selective Activation by Pulsed Laser Irradiation

Study on new process of electroless copper plating pretreatment on carbon fiber surface

Colour-Difference Measurement Method for Evaluation of Quality of Electrolessly Deposited Copper on Polymer after Laser-Induced Selective Activation

Laser-Induced Selective Metallization on Polymer Substrates Using Organocopper for Portable Electronics

Additive and Photochemical Manufacturing of Copper

Fabrication of metallic patterns on ordinary polymer substrates by laser direct activation and electroless plating

Altering the percolation threshold of PA66‐copper hybrid in an electroless copper deposition process by surface activation of the polymer

Facile galvanic replacement deposition of nickel on copper substrate in deep eutectic solvent and its activation ability for electroless Ni–P plating

Selective Metallization on Ordinary Polymer Substrates by Laser Direct Activation of Copper Phosphate or Nickel Phosphate

Laser Induced Selective Activation For Subsequent Autocatalytic Electroless Plating - DTU Orbit (30/10/2017)