Abstract:<p>Manufacturing multi-material part is one of the native advantages of selective laser melting (SLM) due to its layer-by-layer manufacturing method, which is attracting more and more attention in recent years. In an effort to reveal the dual interfacial characterization of dissimilar materials manufactured by SLM with different printing sequences, this paper presents the morphology, microstructure, element distribution, phase composition and microhardness of multi-material interfaces between SLMed 316L steel and C52400 copper alloy. Both interfaces display isolated alloy islands with various shapes and different morphologies. The melt pool at 316L/C52400 interface is deeper and narrower than that at C52400/316L interface. Small 316L and C52400 spheres with a size of 1–5 μm are formed under the surface tension, Marangoni convection in the melt pool and rapid cooling condition, in which many smaller particles with a size of <1 μm appear due to the material supersaturation and convection. Interdiffusion of elements and very fine grains with a size of <6 μm result in excellent metallurgical bonding performance. Cracks tend to originate from the interface and extend to the stainless steel side for both interfaces. No separation of the two materials caused by cracks is found in their contact area. Healing of the cracks by C52400 copper alloy at 316L/C52400 interface is easier to complete. The interface thickness depends on the building sequence of the two materials, which features a much thicker transition when building C52400 on 316L. No intermetallic compound but a trace of CuNi alloy is formed at the interface. The microhardness varies in the transition area due to the existence of isolated 316L/C52400 islands and decreases from 316L to C52400 with the highest value of 283.33 ± 5.51 HV to the lowest value of 181.33 ± 17.62 HV. This research advances the understanding of the different interfacial characterizations of dissimilar materials manufactured by SLM and provides guidance and reference for manufacturing multi-material components with complex interfaces using SLM.</p>

Microstructure and mechanical properties of CuCrZr/316L hybrid components manufactured using selective laser melting

Microstructure and mechanical properties of Cu-Cr-Zr alloy prepared by electron beam additive manufacturing and laser-MIG hybrid welding

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property

Selective laser melting of CuCrZr alloy: processing optimisation, microstructure and mechanical properties

Dual interfacial characterization and property in multi-material selective laser melting of 316L stainless steel and C52400 copper alloy

Additively manufactured CuCrZr alloy: Microstructure, mechanical properties and machinability

Laser–Direct Current arc Hybrid Additive Manufacturing of Cu-Cr-Zr Alloy: Microstructure Evaluation and Mechanical Properties

Interfacial Characteristics and Mechanical Behavior of Hybrid Manufactured AlSi10Mg–Al6061 Bimetal via Selective Laser Melting and Forging

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

Microstructure and Mechanical Properties of Selective Laser Melting 316L/R-316L Butt Joint Welded by Laser Welding

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Selective laser melting of 316L–CuCrZr bimetallic structure via IN718 transition layer

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Tensile Properties of Selective Laser Melted 316L Stainless Steel

Microstructural evolution and mechanical properties of pure Zn fabricated by selective laser melting

The influence of deformation affected region on microstructure and mechanical property of 316L fabricated by hybrid additive-subtractive manufacturing

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Mechanical Properties and Interfacial Characterization of Additive-Manufactured CuZrCr/CoCrMo Multi-Metals Fabricated by Powder Bed Fusion Using Pulsed Wave Laser

Formation mechanism of Al-Zn-Mg-Cu alloy fabricated by laser-arc hybrid additive manufacturing: Microstructure evaluation and mechanical properties

Microstructure and mechanical properties of Al-Fe-Sc-Zr alloy additively manufactured by selective laser melting

Development and experimental validation of a hybrid selective laser melting and CNC milling system