Abstract:The poly(ethylene terephthalate) (PET)/isotactic polypropylene (iPP) in situ microfibrillar blends have been prepared through a “slit die extrusion–hot stretch–quenching” process, in which PET assumes microfibrils with 0.5–15μm in diameter depending on the hot stretching ratios (HSR, the area of the transverse section of the die to the area of the transverse section of the extrudate). The injection molded specimens of virgin iPP and the PET/iPP blends were prepared by conventional injection molding (CIM) and by shear controlled orientation injection molding (SCORIM), respectively. The effect of shear stress and PET phase with different shape on superstructures and their distribution of injection molded microfibrillar samples were investigated by means of small angle X-ray scattering (SAXS) and wide angle X-ray scattering (WAXS). The shear (or elongational) flow during CIM and SCORIM can induce oriented lamellae (i.e. kebabs induced by shish). The shish-kebab structure appears not only in the skin and intermediated layers of CIM samples, but also in the whole region of SCORIM samples. For the neat iPP samples, a more “stretched” shish-kebab structure with higher orientation degree can be obtained in the interior region (intermediate and core layers) by the SCORIM method; moreover, the SCORIM can result in the growth of β-form crystal both in intermediate layer and in core layer, which only appears in intermediate layer of the neat iPP samples obtained by CIM. For the PET/iPP blends, interestingly, the addition of microfibrils as well as their aspect ratios can affect the orientation degree of kebabs only in the intermediate layers, and the addition of microfibrils with a low aspect ratio can bring out a considerable increase in the orientation degree of kebabs along the flow direction. However, for the SCORIM, the addition of microfibrils seems to be a minor effect on the orientation degree of kebabs, and it tends to hamper the formation of a more “stretched” shish-kebab structure and suppresses the growth of β-form crystal distinctly. Furthermore, It appears from experiment that γ-form crystals can grow successfully in this oriented iPP melt with the synergistic effect of shear and pressure only when the growth of β crystals can be restrained by some factors, such as the PET dispersed phase and thermal conditions (cooling rate).

Preparation of PPR/PS Blends by Multiflow Vibration Injection Molding: Influence of Shish–Kebab Structures and In Situ Fibers

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Polypropylene/Polystyrene Blends Prepared by Diffusion and Subsequent Polymerization in Polypropylene Pellets after Injection Molding

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Morphology, thermal behavior, rheological, and mechanical properties of polypropylene/polystyrene blends based on elongation flow

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Investigation of Crystallization, Morphology, and Mechanical Properties of Polypropylene/Polypropylene-Polyethylene Block Copolymer Blends

Mechanical Properties of Injection Molded PP/PET-Nanofibril Composites and Foams

Simultaneously achieving self-toughening and self-reinforcing of polyethylene on an industrial scale using volume-pulsation injection molding

Relationship Between Mechanical Properties and Crystalline Structure of PPR/iPP Blends Modified with β-Nucleator

The Influence of Pressure-Induced-Flow Processing on the Morphology, Thermal and Mechanical Properties of Polypropylene Blends

PMMA-driven morphology modification and dramatic improvement in ductility for PVDF/PLA blends

The Formation of a Highly Oriented Structure and Improvement of Properties in PP/PA6 Polymer Blends during Extrusion-Stretching

Facile approach for largely refining phase domains of PMMA/PS blends and improving their properties during extrusion

Crystalline Morphology of Isotactic Polypropylene (ipp) in Injection Molded Poly(Ethylene Terephthalate) (pet)/ipp Microfibrillar Blends

High Performance Polylactic Acid/thermoplastic Polyurethane Blends with In‐situ Fibrillated Morphology

Study of the Preparation and Dielectric Property of Pp/Sma/Pvdf Blend Material

Tough and Thermostable Polybutylene Terephthalate (PBT)/Vitrimer Blend with Enhanced Interfacial Compatibility

Self-Toughening and Self-Reinforcing of Polypropylene Via Melt-Volume-Pulsation-Induced Crystalline Network

Development of pulsating extensional stress induced melt mixer and its application for polypropylene/carbon fibers composites

Optimization of polypropylene high-strength injection molding welding and interface structure analysis