Abstract:In this study, Ti–Si–C composite coatings were synthesized via plasma spraying of agglomerated powders prepared by a spray drying/precursor pyrolysis technology using Ti, Si, and sucrose powders. The influence of Si content, ranging from 0 wt% to 24 wt%, on the microstructure, mechanical properties, and oxidation resistance of the composite coatings was investigated. Results show that the phase composition of the Ti–Si–C composite coatings changes with the increasing Si content. The coatings without Si addition consist of TiC and Ti3O; the coatings with 6–18 wt% Si are composed of TiC, Ti5Si3, and Ti3O; the coatings with Si content of 24 wt% form only TiC and Ti5Si3 phases. As the Si content increases, the hardness of the Ti–Si–C composite coatings increases first and then decreases, depending on the intrinsic hardness of the ceramic phases, the brittleness of Ti5Si3, and the defects such as pores and cracks. The Ti–Si–C composite coatings have high wear resistance due to the in-situ synthesized high-hardness TiC and Ti5Si3. Owing to the high brittleness of Ti5Si3, the increasing Si content leads to higher wear volume loss at room temperature, which can be partially improved in high-temperature wear tests. The oxidation resistance of Ti–Si–C composite coatings increases with the increase of Si content, and the higher the oxidation temperature, the more obvious the influence of the Si addition on oxidation resistance.

Effect of Si content on the microstructure and properties of CrSi coatings for ATF cladding

Effect of Submicron SiC Particles on the Properties of Alcocrfeni High Entropy Alloy Coatings

Effect of Si on the structure and oxidation behavior of Cr-Si coatings on Zry-4 under high temperature steam environment

Structure, corrosion, and tribological properties of CrSiN coatings with various Si contents in 3.5% NaCl solution

Effect of Si addition to improve the performance of type II and type I hot corrosion resistance of aluminide coating

Effect of Si addition on microstructure and wear behavior of AlCoCrFeNi high-entropy alloy coatings prepared by laser cladding

Xe20+ ions irradiation and autoclave corrosion coupled with steam oxidation behaviors of FeCrAlMoSiY-coated Zr claddings

Effect of Si content on the oxidation behavior of CoCrWSi coatings at 900 °C

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Effect of Si content on the microstructure and properties of Ti–Si–C composite coatings prepared by reactive plasma spraying

Influence of Ag Contents on Structure and Tribological Properties of TiSiN-Ag Nanocomposite Coatings on Ti–6Al–4V

Unveiling the Effect of Si on the Microstructure and Properties of AlFeCoCrNi High Entropy Alloy Coating

Effect of Si Content on the Tribological Properties of Crsin Films in Air and Water Environments

Investigation on Microstructures and High-Temperature Oxidation Resistance of Cr Coatings on Zircaloy-4 by Multi-Arc Ion Plating Technology

Understanding the Corrosion and Tribological Behaviors of CrSiN Coatings with Various Si Contents in HCl Solution

Effects of silicon content on the structure and mechanical properties of (AlCrTaTiZr)–Six–N coatings by reactive RF magnetron sputtering

Effect of Cr/Al Atomic Ratio on the Oxidation Resistance in 1200°C Steam for the CrAlSiN Coatings Deposited on Zr Alloy Substrates

Systematic investigations on the microstructural evolution and degradation mechanism of Cr 3 Si-coated Zry-4 under DBA and BDBA conditions

Microstructure, Mechanical, and Electrochemical Properties of SiC Particle Reinforced CoCrFeNiCu High-Entropy Alloy Coatings

Effects of silicon content on the structure and mechanical properties of (AlCrTaTiZr)–Si<sub><i>x</i></sub>–N coatings by reactive RF magnetron sputtering

Microstructure Evolution and Wear Mechanism of Si-Effected Al0.6CoCrFeNi High-Entropy Alloy Coatings by Laser Cladding