Abstract:Summary Sustained injection of industrial-scale volumes of cold CO2 into warmer subsurface rock will result in extensive cooling which can alter rock mass mechanical behavior and fluid migration characteristics. Advanced simulation tools are available to assess and characterize such phenomena; however, the effective use of these tools requires appropriate injection temperatures and rock thermophysical parameters (in addition to geomechanical and hydraulic properties). The primary objective of this study was to demonstrate the sensitivity of injection-induced tensile fracturing and fault reactivation to injection temperature and reservoir thermophysical properties during CO2 injection operations. This was achieved by (1) compiling and reviewing thermophysical parameter data available for formations in the province of Alberta, Canada, and CO2 injection temperature records for CO2 injection projects in western Canada and (2) using a 3D, physics-based, fully integrated hydraulic fracturing and reservoir simulation numerical model to examine the geomechanical response of several potential CO2 reservoirs in the Alberta Basin as a function of injection temperature, thermal conductivity (TC), and coefficient of linear thermal expansion (CLTE) values. The simulation results indicate that reducing the fluid injection temperature from 15°C (assumed in previous work) to 2°C (conservative value selected based on temperature data reviewed in this work) could trigger extensive vertical (20–130 m high, 100–600 m long) tensile fractures with rapid fracture initiation and full vertical growth within short periods (weeks to months) and continued horizontal length increase. When low values for thermophysical properties are used, the results show that thermally-induced tensile fracturing is unlikely, whereas the use of high values results in extensive tensile fracturing in all simulations. A similar conclusion was reached for the thermally-induced reactivation (unclamping) of proximal, critically-stressed faults. Notably, slip is predicted for all simulations where high thermophysical property values are used. This confirms that accurate determination of minimum fluid injection temperature and thermophysical parameters is important for containment risk assessment for commercial-scale CO2 storage projects. Another significant outcome of this work is the observation that most thermophysical parameters in the available data were measured using experimental conditions and/or temperature paths that are not representative of CO2 injection projects. As such, the development and validation of best practice approaches for accurate assessment of these parameters seem necessary.

Transient Joule–Thomson cooling during CO 2 injection in depleted reservoirs

Joule-Thomson cooling of CO2 injected into aquifer under heat exchange with adjacent formations by Newtons law- 1D exact solution

Semi-Analytical Temperature and Stress Profiles for Nonisothermal CO2 Injection

Thermal Modelling In And Around A Co2 Injector

Injection Temperature Impacts on Reservoir Response during CO2 Storage

Numerical investigation on wellbore temperature and pressure during carbon dioxide fracturing

CO2 flow modeling in a coupled wellbore and aquifer system: Details of pressure, temperature, and dry-out

Thermal Impact of Co2 Injection on Geomechanical Response at the Futuregen 2.0 Site: A Three-Dimensional Thermo-Geomechanical Approach

Modeling the impact of thermal stresses induced by wellbore cooldown on the breakdown pressure and geometry of a hydraulic fracture

Flow and Thermal Modeling of CO2 in Injection Well During Geological Sequestration

The Sensitivity Analysis of Wellbore Heat Transfer During the Co2 Injection Process

The Sensitivity Analysis of Wellbore Heat Transfer during the CO<sub>2</sub> Injection Process

Modeling of wellbore dynamics of a CO 2 injector during transient well shut-in and start-up operations

The use of supercritical CO2 in deep geothermal reservoirs as a working fluid: Insights from coupled THMC modeling

Analysis of CO2 phase transition within well-bore during injection into low-rank but relatively shallow coal seams

Numerical investigation of wellbore temperature and pressure fields in CO2 fracturing

Modelling and Interpretation of a Temperature Drop in the Wellbore in Ordos CO2 Storage Project, China

Thermal recovery of coalbed methane: Modeling of heat and mass transfer in wellbores

Thermo‐poroelastic responses of a pressure‐driven fracture in a carbon storage reservoir and the implications for injectivity and caprock integrity

Research on Temperature–Pressure Coupling Model of Gas Storage Well during Injection Production

Computational Fluid Dynamics Modeling and Analysis of Axial and Radial Temperature of Wellbore during Injection and Production Process