Abstract:Micro thermoelectric generator (μ-TEG) attracts more and more attention due to its small size and high power density. Many two-dimensional thermoelectric materials with high performance have facilitated the development of μ-TEG. However, the performance of μ-TEG fabricated by these great thermoelectric materials is significantly degraded due to size effect, interfacial effects (include contact effect and boundary effect) and structure effect. To accurately assess the performance degradation degree from material to μ-TEG and guide the device fabrication, an experiment-verified mathematical model considering interfacial and size effects is proposed. Firstly, the phonon/electron temperature distribution in thermoelectric leg of μ-TEG is analyzed to investigate the device-level thermoelectric properties of material. Then based on the device-level thermoelectric properties, the actual power generation performance model of μ-TEG is established to conduct the influence analysis of these effects (boundary, size, contact and structure effects) on material and device. Finally, the thermoelectric leg thickness ( H te ) is optimized to realize optimal power generation. The study results reveal that boundary and size effects weaken the device-level thermoelectric properties, and the reduction trend is more obvious when H te is smaller, especially when H te ≤ 20 μm. The decrease from the material intrinsic figure of merit ( (ZT) m ) to the device figure of merit ( (ZT) D ) is owing to the boundary effect, structure effect and contact effect, and the dominant factor of this decrease changes from structure effect ( H te <7 μm)to contact effect ( H te ≥ 7 μm) as H te increases, which points to a main optimization direction for (ZT) D for different H te . As for contact effect, the electrical contact resistivity ( r e,c ) has a more significant impact on weakening the performance of μ-TEG than thermal contact resistivity ( r k,c ), and their optimization goals are explored ( r e,c ≤ 5.1 × 10 −12 Ω·m 2 , r k,c ≤ 9.3 × 10 −8 K·m 2 /W). At given electrical and thermal contact resistivity, there exists an optimal H te for achieving the optimal power generation ( P opt ) and a large range of H te for achieving 95% P opt , and the optimal H te increases with increasing electrical and thermal contact resistivity. This study can reduce the processing difficulty and save time and economic costs of μ-TEG fabrication, which can avoid the blind fabrication of μ-TEG.

Inverse optimization investigation for thermoelectric material from device level

Design Optimization of Thermoelectric Cooling Systems for Applications in Electronic Devices

Optimizing GeTe-based thermoelectric generator for low-grade heat recovery

Numerical analysis of thermoelectric power generation coupled with temperature-dependent material properties

Performance Investigation and Optimization of an L-type Thermoelectric Generator

A Novel Optimization Method for TEG System Performance Based on Temperature and Heat Flux

Challenges and strategies to optimize the figure of merit: Keeping eyes on thermoelectric metamaterials

Thermal management of a flexible controlled thermoelectric energy conversion-utilization system using a multi-objective optimization

Performance degradation analysis and fabrication guidance of μ-TEG from material to device

Novel principle for characterizing the material-level parameters of a thermoelectric generator module

Compromise and Synergy in High‐Efficiency Thermoelectric Materials

Compromise and Synergy in High-Efficiency Thermoelectric Materials.

Analysis on optimal length scale of thermoelectric generators when using different circuit layouts

Searching For The Best Thermoelectrics Through The Optimization Of Transport Distribution Function

Thermoelectric Device Performance Beyond Average ZT: Holistic Consideration of Materials and Design

A Comprehensive Review of Strategies and Approaches for Enhancing the Performance of Thermoelectric Module

Impact of internal connections and heat loss on simulated large-scale low-temperature thermoelectric generation system

Evaluation of Parameters Coupling into ZT for Higher Output Performance

A comprehensive review of thermoelectric generation optimization by statistical approach: Taguchi method, analysis of variance (ANOVA), and response surface methodology (RSM)

Optimization of segmented thermoelectric devices composed of high-temperature thermoelectric material La2Te3

Advantage of a Thermoelectric Generator with Hybridization of Segmented Materials and Irregularly Variable Cross-Section Design