Abstract:Heavy metal-based vehicle caused increase in fuel consumption, which creates pollution in the environment; thus, scientists across the nation researched to produce light weight, cost-effective, easy degradable, corrosive resistant composite material. Due to such features present in the composite material, the present research aims to examine the impact of alkali-silane treatment on the time-dependent and machining behavior of composites. Further, the alkali treatment and silane treatment on fiber and filler particle are carried out to provide even dispersion of filler particle and better reinforcement and interfacial bonding adhesion to the composite material, which makes a novelty to this study. The obtained fiber and filler particle were reinforced to matrix by using hand layup method and subsequently cured. This prepared composite material's strength is analyzed as per the ASTM standards. The results indicate that the inclusion of surface modified corn-fiber reinforced EF composite shows stronger interfacial adhesion, which implies loss factor of 42.8% lower than neat epoxy. Similarly, reinforcing corn husk fiber increases the energy release rate by 2500% and the fracture toughness by 156.47% when compared to pure epoxy composite. Further, the inclusion of biosilica particle of 2.0 vol.% exhibited the highest storage modulus of 5.69 GPa and the lowest loss factor of 0.32. This demonstrates the beneficial effect of combining alkali and silane treatment on corn fiber and filler particle. The epoxy composite (EFP3) of chemically treated fiber 30 vol.% and 2 vol.% of biosilica reinforcement exhibits a higher fatigue life cycle, fracture toughness, and energy release rate of 30,546, 26.5 MPa√m, and 0.86 MJ/m 2 , respectively. Similarly, the composite designation EFP3 has the lowest contact angle of 78°, indicating the preserved hydrophobicity. A drilling study has shown that using a 4-mm drill bit and 8-mm drill bit. The resultant of the drilling studies concludes that the use of 2.0 vol.% biosilica reduced the occurrence of fiber pull-out while drilling. Owing to such improved strength properties, light weight, corrosive resistant features in the biocomposite are applied in industries such as automotive, sporting goods, food and drug packaging, aerospace, and other technical applications that require strong load-bearing capacity, etc.

Influence of silicious rock dust on mechanical, thermal and flammability behaviour of Himalayan nettle fibre-reinforced vinyl ester composite

Impact of temperature aging on behavioral changes in vinyl ester composite reinforced with Himalayan nettle fiber and silicious rock dust

Effect of adding Urtica dioica–chopped fiber on load bearing, wear, fatigue, thermal stability, flammability, and water absorption behavior of rock dust dispersed vinyl ester composite

Influence of heat treated fox tail millet husk biosilica on dynamic properties of nettle fibre-reinforced vinyl ester composite

Characterization of peanut husk-derived Si3N4 basalt fiber-reinforced unsaturated polyester resin composites

Flame retardant, load bearing and thermal studies on satin weaved sunn hemp fibre and cashew nut shell de-oiled cake biosilica epoxy composites

Load Bearing, Time Dependent, Thermal and Flame Retardant Behavior of Peanut Husk Derived Si3N4 Basalt Fibre-Reinforced Polyester Composite

Effect of rice husk ash silicon nitride on mechanical, wear, thermal conductivity, and flammability behavior of aluminized glass-kenaf fiber-reinforced polyester composite

Influence of peanut husk derived heat-treated Si3N4 on load bearing properties of basalt fibre-reinforced polyester composite

A characterization study on toughening vinyl ester composites using annealed biosilica from fox tail millet husk and nettle fiber

Mechanical, wear and thermal behaviour of rice husk microfibre and ZrO2 bioceramic from Phyllanthus niruri extracts reinforced vinyl ester composites

Sustainable Engineering of Human Hair Fiber-Composite in Engineering Application

A Characterization Study on Toughening Vinyl Ester Composites Using Annealed Vinyl Silane Functionalized Biosilica from Foxtail Millet Husk and Nettle Fibre

Sustainable engineering applications using jute-basalt fiber reinforced composites: A material characterization study

Enhancing sustainable composites: isolation of nanocellulose from Selenicereus undatus (dragon fruit) and kenaf fiber reinforcement in vinyl ester matrix—a study on mechanical, wear, fatigue, creep, and dynamic mechanical properties

Influence of silica and alumina nanoparticles on the wear and mechanical behavior of Indian almond fiber reinforced natural composites

Evaluation of mechanical and erosive wear properties of hybrid nano composites basalt/E-glass fiber + MWCNTs/SiO 2

Influence of nano-silica on mechanical properties of Indian almond fiber reinforced hybrid epoxy composites

Characterization of heat-treated biosilica from biomass waste fox tail millet husks and banana fiber reinforced epoxy composite

Valorisation of corn waste as fiber, biosilica, and their epoxy composites: fatigue, fracture toughness, water absorption, and drilling properties

Effect of a synthesized chitosan flame retardant on the flammability, thermal properties, and mechanical properties of vinyl ester/bamboo nonwoven fiber composites